ATMEGA8515-16PU Atmel, ATMEGA8515-16PU Datasheet - Page 132

• Manufacturer Part Number: ATMEGA8515-16PU
• Description: IC AVR MCU 8K 16MHZ 5V 40DIP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8515-16PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Cpu Speed: 16 MIPS
• Eeprom Memory: 512 Bytes
• Input Output: 35
• Interface: SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 40-pin PDIP
• Programmable Memory: 8K Bytes
• Timers: 1-8-bit, 1-16-bit
• Voltage, Range: 4.5-5.5 V
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 2
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

132
ATmega8515(L)
be cleared, and SPIF in SPSR will become set. The user will then have to set MSTR to
re-enable SPI Master mode.
• Bit 3 – CPOL: Clock Polarity
When this bit is written to one, SCK is high when idle. When CPOL is written to zero,
SCK is low when idle. Refer to Figure 62 and Figure 63 for an example. The CPOL func-
tionality is summarized below:
Table 56. CPOL Functionality
• Bit 2 – CPHA: Clock Phase
The settings of the Clock Phase bit (CPHA) determine if data is sampled on the leading
(first) or trailing (last) edge of SCK. Refer to Figure 62 and Figure 63 for an example.
The CPHA functionality is summarized below:
Table 57. CPHA Functionality
• Bits 1, 0 – SPR1, SPR0: SPI Clock Rate Select 1 and 0
These two bits control the SCK rate of the device configured as a Master. SPR1 and
SPR0 have no effect on the Slave. The relationship between SCK and the Oscillator
Clock frequency f
Table 58. Relationship Between SCK and the Oscillator Frequency
SPI2X
CPOL
CPHA
0
0
0
0
1
1
1
1
0
1
0
1
osc
is shown in the following table:
SPR1
0
0
1
1
0
0
1
1
Leading Edge
Leading Edge
Sample
Falling
Rising
Setup
SPR0
0
1
0
1
0
1
0
1
SCK Frequency
f
f
f
f
f
f
f
f
osc
osc
osc
osc
osc
osc
osc
osc
/
/
/
/
/
/
/
/
4
16
64
128
2
8
32
64
Trailing Edge
Trailing Edge
Sample
Falling
Rising
Setup
2512K–AVR–01/10