ATMEGA2560V-8AU Atmel, ATMEGA2560V-8AU Datasheet - Page 210

• Manufacturer Part Number: ATMEGA2560V-8AU
• Description: IC AVR MCU 256K 8MHZ 100TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA2560V-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 256KB (128K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Processor Series: ATMEGA256x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 8 KB
• Interface Type: 2-Wire, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 86
• Number Of Timers: 6
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• A/d Inputs: 16-Channel, 10-Bit
• Cpu Speed: 8 MIPS
• Eeprom Memory: 4K Bytes
• Input Output: 86
• Interface: 2-Wire/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 100-pin TQFP
• Programmable Memory: 256K Bytes
• Timers: 2-8-bit, 4-16-bit
• Voltage, Range: 1.8-5.5 V
• Package: 100TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 8 MHz
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK503 - STARTER KIT AVR EXP MODULE 100PATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

21.3.1
21.4
2549M–AVR–09/10
USART Initialization
Parity Bit Calculation
Figure 21-4. Frame Formats
The frame format used by the USART is set by the UCSZn2:0, UPMn1:0 and USBSn bits in
UCSRnB and UCSRnC. The Receiver and Transmitter use the same setting. Note that changing
the setting of any of these bits will corrupt all ongoing communication for both the Receiver and
Transmitter.
The USART Character SiZe (UCSZn2:0) bits select the number of data bits in the frame. The
USART Parity mode (UPMn1:0) bits enable and set the type of parity bit. The selection between
one or two stop bits is done by the USART Stop Bit Select (USBSn) bit. The Receiver ignores
the second stop bit. An FE (Frame Error) will therefore only be detected in the cases where the
first stop bit is zero.
The parity bit is calculated by doing an exclusive-or of all the data bits. If odd parity is used, the
result of the exclusive or is inverted. The parity bit is located between the last data bit and first
stop bit of a serial frame. The relation between the parity bit and data bits is as follows::
The USART has to be initialized before any communication can take place. The initialization pro-
cess normally consists of setting the baud rate, setting frame format and enabling the
Transmitter or the Receiver depending on the usage. For interrupt driven USART operation, the
Global Interrupt Flag should be cleared (and interrupts globally disabled) when doing the
initialization.
Before doing a re-initialization with changed baud rate or frame format, be sure that there are no
ongoing transmissions during the period the registers are changed. The TXCn Flag can be used
to check that the Transmitter has completed all transfers, and the RXC Flag can be used to
St
(n)
P
Sp
IDLE
P
P
d
even
odd
n
(IDLE)
St
must be high.
Start bit, always low.
Data bits (0 to 8).
Parity bit. Can be odd or even.
Stop bit, always high.
No transfers on the communication line (RxDn or TxDn). An IDLE line
Parity bit using even parity.
Parity bit using odd parity.
Data bit n of the character.
P
0
P
even
odd
1
=
=
ATmega640/1280/1281/2560/2561
d
d
2
n 1
n 1
–
–
3
⊕
⊕
…
…
4
⊕
⊕
FRAME
[5]
d
d
3
3
⊕
⊕
[6]
d
d
2
2
⊕
⊕
[7]
d
d
1
1
[8]
⊕
⊕
d
d
0
0
[P]
⊕
⊕
0
1
Sp1 [Sp2]
(St / IDLE)
210