LPC2103FHN48H/6,51 NXP Semiconductors, LPC2103FHN48H/6,51 Datasheet - Page 13

• Manufacturer Part Number: LPC2103FHN48H/6,51
• Description: IC ARM7 MCU FLASH 32K 48HVQFN
• Manufacturer: NXP Semiconductors
• Series: LPC2100r

Specifications of LPC2103FHN48H/6,51

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-VQFN Exposed Pad, 48-HVQFN, 48-SQFN, 48-DHVQFN
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 70MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC21
• Core: ARM7 TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 70 MHz
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, DB-LQFP48-LPC2103, MCB2103, MCB2103U, MCB2103UME, KSK-LPC2103-01, KSK-LPC2103-01PL, KSK-LPC2103-02
• Development Tools By Supplier: OM10079, OM10081, OM10090
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935288984518

NXP Semiconductors
LPC2101_02_03_4
Product data sheet
6.7.1 Features
6.8.1 Features
6.9.1 Features
6.7 Fast general purpose parallel I/O
6.8 10-bit ADC
6.9 UARTs
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back, as well as the current state of the port pins.
LPC2101/02/03 introduce accelerated GPIO functions over prior LPC2000 devices:
The LPC2101/02/03 contain one ADC. It is a single 10-bit successive approximation ADC
with eight channels.
The LPC2101/02/03 each contain two UARTs. In addition to standard transmit and
receive data lines, UART1 also provides a full modem control handshake interface.
Compared to previous LPC2000 microcontrollers, UARTs in LPC2101/02/03 include a
fractional baud rate generator for both UARTs. Standard baud rates such as 115200 can
be achieved with any crystal frequency above 2 MHz.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
GPIO registers are relocated to the ARM local bus for the fastest possible I/O timing.
Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
All GPIO registers are byte addressable.
Entire port value can be written in one instruction.
Bit-level set and clear registers allow a single instruction set or clear of any number of
bits in one port.
Direction control of individual bits.
Separate control of output set and clear.
All I/O default to inputs after reset.
Measurement range of 0 V to 3.3 V.
Each converter capable of performing more than 400,000 10-bit samples per second.
Burst conversion mode for single or multiple inputs.
Optional conversion on transition on input pin or Timer Match signal.
Every analog input has a dedicated result register to reduce interrupt overhead.
16 byte Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1, 4, 8, and 14 bytes
Rev. 04 — 2 June 2009
Single-chip 16-bit/32-bit microcontrollers
LPC2101/02/03
© NXP B.V. 2009. All rights reserved.
13 of 37