ST10R172LT1 STMicroelectronics, ST10R172LT1 Datasheet - Page 34

• Manufacturer Part Number: ST10R172LT1
• Description: MCU 16BIT ROMLESS LV 100TQFP
• Manufacturer: STMicroelectronics
• Series: ST10r

Specifications of ST10R172LT1

• Core Processor: ST10
• Core Size: 16-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 77
• Program Memory Type: ROMless
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 100-TQFP, 100-VQFP
• Controller Family/series: ST10
• No. Of I/o's: 77
• Ram Memory Size: 1KB
• Cpu Speed: 50MHz
• No. Of Timers: 5
• Embedded Interface Type: SPI, USART
• No. Of Pwm Channels: 1
• Rohs Compliant: Yes
• Processor Series: ST10R1x
• Core: ST10
• Data Bus Width: 16 bit
• Data Ram Size: 1 KB
• Interface Type: SSP, USART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 77
• Number Of Timers: 5
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: In Transition

ST10R172L - ELECTRICAL CHARACTERISTICS
34/68
1
Parameter
PORT0 configuration current
RPD pulldown current
XTAL1 input current
Pin capacitance
(digital inputs/outputs)
Power supply current
Idle mode supply current
Power-down mode supply current
1) This specification is not valid for outputs which are switched to open drain mode. In this case
2) This specification is only valid during reset, or interruptible power-down mode, after recep-
3) This specification is only valid during reset, hold or adapt-mode. Port 6 pins are only affected
4) The maximum current may be drawn while the signal line remains inactive.
5) The minimum current must be drawn in order to drive the signal line active.
6) Not 100% tested, guaranteed by design characterization.
7) Supply current is a function of operating frequency as illustrated in Figure 7 on page 35.
8) Typical value at 25°C = 20µA.
9) This parameter is tested including leakage currents. All inputs (including pins configured as
the respective output will float and the resulting voltage comes from the external circuitry.
tion of an external interrupt signal that will wake up the CPU.
if they are used for CS output and the open drain function is not enabled.
This parameter is tested at V
and all inputs at V
memory (16-bit demux bus mode, no waitstates, no memory tri-state waitstates, normal
ALE).
inputs) at 0 V to 0.1 V or at V
figured as outputs) disconnected.
6)
2
IL
or V
3
IH
with an infinite execution of NOP instruction fetched from external
Table 11 DC characteristics
Symbol
I
I
I
I
C
I
I
I
P0H
P0L
RPD
IL
CC
ID
PD
DD
DD
IO
8
max and 50 MHz CPU clock with all outputs disconnected
5
– 0.1 V to V
4
5
CC
CC
Limit Values
min.
–
-50
100
–
–
–
–
–
DD
, V
REF
= 0 V, all outputs (including pins con-
max.
-4
–
500
±20
10
15 +
2.5 * f
10 +
0.9 * f
200
CPU
CPU
Unit
pF
mA
mA
A
A
A
A
A
Test Condition
V
V
V
0 V <
f
T
f
RSTIN =
f
V
CPU
CPU
= 1 MHz
IN
IN
OUT
A
DD
= 25 °C
= V
= V
= 3.6 V
in [MHz]
in [MHz]
= V
V
IHmin
ILmax
IN
DD
V
<
IH1
V
9
DD
7))
7