W77E058A40DL Nuvoton Technology Corporation of America, W77E058A40DL Datasheet - Page 65

• Manufacturer Part Number: W77E058A40DL
• Description: IC MCU 8-BIT 32K FLASH 40-DIP
• Manufacturer: Nuvoton Technology Corporation of America
• Series: W77r

Specifications of W77E058A40DL

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, Serial Port
• Peripherals: POR, WDT
• Number Of I /o: 32
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP
• Cpu Family: W77
• Device Core: 8051
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: UART
• Total Internal Ram Size: 1KB
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

The 16 states of the counter effectively divide the bit time into 16 slices. The bit detection is done on a
best of three basis. The bit detector samples the RxD pin, at the 8th, 9th and 10th counter states. By
using a majority 2 of 3 voting system, the bit value is selected. This is done to improve the noise
rejection feature of the serial port. If the first bit detected after the falling edge of RxD pin is not 0, then
this indicates an invalid start bit, and the reception is immediately aborted. The serial port again looks
for a falling edge in the RxD line. If a valid start bit is detected, then the rest of the bits are also
detected and shifted into the SBUF.
After shifting in 8 data bits, there is one more shift to do, after which the SBUF and RB8 are loaded
and RI is set. However certain conditions must be met before the loading and setting of RI can be
done.
If these conditions are met, then the stop bit goes to RB8, the 8 data bits go into SBUF and RI is set.
Otherwise the received frame may be lost. After the middle of the stop bit, the receiver goes back to
looking for a 1-to-0 transition on the RxD pin.
(SMOD_1)
SMOD=
TCLK
RCLK
Overflow
Timer 1
1. RI must be 0 and
2. Either SM2 = 0, or the received stop bit = 1.
RXD
2
0
SAMPLE
0
0
1
(for Serial Port 0 only)
1
1
DETECTOR
Timer 2 Overflow
1-TO-0
16
16
Write to
SBUF
START
RX CLOCK
TX CLOCK
TX START
CONTROLLER
DETECTOR
RX
SERIAL
Figure 21. Serial Port Mode 1
BIT
Data Bus
TX SHIFT
RX SHIFT
Internal
LOAD
SBUF
- 65 -
TI
RI
Receive Shift Register
CLOCK
SIN
Transmit Shift Register
PAROUT
STOP
START
LOAD
CLOCK
PARIN
D8
Publication Release Date: April 17, 2007
SOUT
SBUF
RB8
Serial Port
W77E058A
SBUF
Interrupt
Read
TXD
Revision A10
Internal
Data
Bus