C8051F311-GMR Silicon Laboratories Inc, C8051F311-GMR Datasheet - Page 161

• Manufacturer Part Number: C8051F311-GMR
• Description: IC 8051 MCU 16K FLASH 28MLP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F31xr

Specifications of C8051F311-GMR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 17x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Package: 24QFN EP
• Device Core: 8051
• Family Name: C8051F31x
• Maximum Speed: 25 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 25
• Interface Type: I2C/SMBus/SPI/UART
• On-chip Adc: 17-chx10-bit
• Number Of Timers: 4
• For Use With: 336-1446 - ADAPTER PROGRAM TOOLSTICK F311336-1253 - DEV KIT FOR C8051F310/F311
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

14.6. SMBus Status Decoding
The current SMBus status can be easily decoded using the SMB0CN register. In the table below, STATUS
VECTOR refers to the four upper bits of SMB0CN: MASTER, TXMODE, STA, and STO. Note that the
shown response options are only the typical responses; application-specific procedures are allowed as
long as they conform to the SMBus specification. Highlighted responses are allowed but do not conform to
the SMBus specification.
1100
1000
1110
Values Read
0
0
0
1
0
0
0
0
X
X
0
1
Current SMbus State
A master START was
generated.
A master data or address byte
was transmitted; NACK
received.
A master data or address byte
was transmitted; ACK
received.
A master data byte was
received; ACK requested.
Table 14.4. SMBus Status Decoding
Rev. 1.7
C8051F310/1/2/3/4/5/6/7
Typical Response Options
Load slave address + R/W into
SMB0DAT.
Set STA to restart transfer.
Abort transfer.
Load next data byte into
SMB0DAT.
End transfer with STOP.
End transfer with STOP and start
another transfer.
Send repeated START.
Switch to Master Receiver Mode
(clear SI without writing new data
to SMB0DAT).
Acknowledge received byte; Read
SMB0DAT.
Send NACK to indicate last byte,
and send STOP.
Send NACK to indicate last byte,
and send STOP followed by
START.
Send ACK followed by repeated
START.
Send NACK to indicate last byte,
and send repeated START.
Send ACK and switch to Master
Transmitter Mode (write to
SMB0DAT before clearing SI).
Send NACK and switch to Master
Transmitter Mode (write to
SMB0DAT before clearing SI).
0
1
0
0
0
1
1
0
0
0
1
1
1
0
0
Written
Values
0
0
1
0
1
1
0
0
0
1
1
0
0
0
0
161
X
X
X
X
X
X
X
X
1
0
0
1
0
1
0