C8051F504-IQ Silicon Laboratories Inc, C8051F504-IQ Datasheet - Page 219

• Manufacturer Part Number: C8051F504-IQ
• Description: IC 8051 MCU 32K FLASH 48-QFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F50xr

Specifications of C8051F504-IQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-QFP
• Mfg Application Notes: LIN Bootloader AppNote
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), CAN, LIN, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 40
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 32x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 40
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F500DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 32-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1527 - KIT DEV FOR C8051F50X
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1518

22.1. Bosch CAN Controller Operation
The CAN Controller featured in the C8051F500/2/4/6/8-F510 devices is a full implementation of Bosch’s
full CAN module and fully complies with CAN specification 2.0B. A block diagram of the CAN controller is
shown in Figure 22.2. The CAN Core provides shifting (CANTX and CANRX), serial/parallel conversion of
messages, and other protocol related tasks such as transmission of data and acceptance filtering. The
message RAM stores 32 message objects which can be received or transmitted on a CAN network. The
CAN registers and message handler provide an interface for data transfer and notification between the
CAN controller and the CIP-51.
The function and use of the CAN Controller is detailed in the Bosch CAN User’s Guide. The User’s Guide
should be used as a reference to configure and use the CAN controller. This data sheet describes how to
access the CAN controller.
All of the CAN controller registers are located on SFR Page 0x0C. Before accessing any of the CAN regis-
ters, the SFRPAGE register must be set to 0x0C.
The CAN Controller is typically initialized using the following steps:
1. Set the SFRPAGE register to the CAN registers page (page 0x0C).
2. Set the INIT and the CCE bits to 1 in CAN0CN. See the CAN User’s Guide for bit definitions.
3. Set timing parameters in the Bit Timing Register and the BRP Extension Register.
4. Initialize each message object or set its MsgVal bit to NOT VALID.
5. Reset the INIT bit to 0.
22.1.1. CAN Controller Timing
The CAN controller’s clock (f
is accurate to within 0.5% of 24 MHz across the entire temperature range and for VDD voltages greater
than or equal to the minimum output of the on-chip voltage regulator, and so an external oscillator is not
required for CAN communication for most systems. Refer to Section “4.10.4 Oscillator Tolerance Range” in
the Bosch CAN User’s Guide for further information regarding this topic.
CAN Controller
(32 Objects)
Message
Message
Handler
RAM
sys
) is derived from the CIP-51 system clock (SYSCLK). The internal oscillator
Figure 22.2. CAN Controller Diagram
RX
CAN Core
Rev. 1.2
TX
CAN0CFG
C8051F50x/F51x
System Clock
8051 MCU Core
CAN Registers
SFR space
mapped to
219