MC908GP32CBE Freescale Semiconductor, MC908GP32CBE Datasheet - Page 209

• Manufacturer Part Number: MC908GP32CBE
• Description: IC MCU 32K FLASH 8MHZ 42-SDIP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GP32CBE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 31
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 42-DIP (0.600", 15.24mm)
• Controller Family/series: HC08
• No. Of I/o's: 31
• Ram Memory Size: 512Byte
• Cpu Speed: 8MHz
• No. Of Timers: 1
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GP
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 33
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

TOIE — TIM Overflow Interrupt Enable Bit
TSTOP — TIM Stop Bit
TRST — TIM Reset Bit
PS[2:0] — Prescaler Select Bits
17.9.2 TIM Counter Registers
The two read-only TIM counter registers contain the high and low bytes of the value in the TIM counter.
Reading the high byte (TCNTH) latches the contents of the low byte (TCNTL) into a buffer. Subsequent
reads of TCNTH do not affect the latched TCNTL value until TCNTL is read. Reset clears the TIM counter
registers. Setting the TIM reset bit (TRST) also clears the TIM counter registers.
Freescale Semiconductor
This read/write bit enables TIM overflow interrupts when the TOF bit becomes set. Reset clears the
TOIE bit.
This read/write bit stops the TIM counter. Counting resumes when TSTOP is cleared. Reset sets the
TSTOP bit, stopping the TIM counter until software clears the TSTOP bit.
Setting this write-only bit resets the TIM counter and the TIM prescaler. Setting TRST has no effect on
any other registers. Counting resumes from $0000. TRST is cleared automatically after the TIM
counter is reset and always reads as logic 0. Reset clears the TRST bit.
These read/write bits select one of the seven prescaler outputs as the input to the TIM counter as
Table 17-2
1 = TIM overflow interrupts enabled
0 = TIM overflow interrupts disabled
1 = TIM counter stopped
0 = TIM counter active
1 = Prescaler and TIM counter cleared
0 = No effect
shows. Reset clears the PS[2:0] bits.
Do not set the TSTOP bit before entering wait mode if the TIM is required
to exit wait mode.
Setting the TSTOP and TRST bits simultaneously stops the TIM counter at
a value of $0000.
PS2
0
0
0
0
1
1
1
1
PS1
0
0
1
1
0
0
1
1
Table 17-2. Prescaler Selection
MC68HC908GP32 Data Sheet, Rev. 10
PS0
0
1
0
1
0
1
0
1
NOTE
NOTE
Internal bus clock ÷ 16
Internal bus clock ÷ 32
Internal bus clock ÷ 64
Internal bus clock ÷ 1
Internal bus clock ÷ 2
Internal bus clock ÷ 4
Internal bus clock ÷ 8
TIM Clock Source
Not available
I/O Registers
209