M30281F6HP#U3B Renesas Electronics America, M30281F6HP#U3B Datasheet - Page 382

• Manufacturer Part Number: M30281F6HP#U3B
• Description: IC M16C/28 MCU FLASH 48K 64LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/28r

Specifications of M30281F6HP#U3B

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, POR, PWM, Voltage Detect, WDT
• Number Of I /o: 55
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: R0K330290S000BE - KIT EVAL STARTER FOR M16C/29M30290T2-CPE - EMULATOR COMPACT M16C/26A/28/29M30290T2-CPE-HP - EMULATOR COMPACT FOR M16C/TINY
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M
R
R
20.6 Timer
e
E
1
. v
J
6
0
20.6.1 Timer A
C
2
9
2 /
0 .
B
20.6.1.1 Timer A (Timer Mode)
20.6.1.2 Timer A (Event Counter Mode)
0
0
8
0
1. The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR
2. While counting is in progress, the counter value can be read out at any time by reading the TAi
3. If a low-level signal is applied to the SD pin when the IVPCR1 bit in the TB2SC register is set to “1”
1. The timer remains idle after reset. Set the mode, count source, counter value, etc. using the TAiMR
2. While counting is in progress, the counter value can be read out at any time by reading the TAi
3. If a low-level signal is applied to the SD pin when the IVPCR1 bit in the TB2SC register is set to “1”
G
4
J
7
a
o r
(i = 0 to 4) register and the TAi register before setting the TAiS bit in the TABSR register to “1” (count
starts).
Always make sure the TAiMR register is modified while the TAiS bit remains “0” (count stops)
regardless whether after reset or not.
register. However, if the TAi register is read at the same time the counter is reloaded, the read value
is always “FFFF
counting, the read value is the one that has been set in the register.
(three-phase output forcible cutoff by input on SD pin enabled), the TA1
pins go to a high-impedance state.
(i = 0 to 4) register, the TAi register, the UDF register, the ONSF register TAZIE, TA0TGL and
TA0TGH bits and the TRGSR register before setting the TAiS bit in the TABSR register to “1” (count
starts).
Always make sure the TAiMR register, the UDF register, the ONSF register TAZIE, TA0TGL and
TA0TGH bits and the TRGSR register are modified while the TAiS bit remains “0” (count stops)
regardless whether after reset or not.
register. However, if the TAi register is read at the same time the counter is reloaded, the read value
is always “FFFF
flows. If the TAi register is read after setting a value in it, but before the counter starts counting, the
read value is the one that has been set in the register.
(three-phase output forcible cutoff by input on SD pin enabled), the TA1
pins go to a high-impedance state.
0 -
. n
u
2
3
p
0
, 1
0
(
M
2
0
1
0
6
7
C
2 /
page 360
, 8
16
M
16
1
”. If the TAi register is read after setting a value in it, but before the counter starts
” when the timer counter underflows and “0000
6
C
2 /
f o
8
3
) B
8
5
_____
_____
_____
_____
16
” when the timer counter over-
OUT
OUT
, TA2
, TA2
OUT
OUT
20. Precautions
and TA4
and TA4
OUT
OUT