SAF-XE164G-24F66L AC Infineon Technologies, SAF-XE164G-24F66L AC Datasheet - Page 71

• Manufacturer Part Number: SAF-XE164G-24F66L AC
• Description: IC MCU 16BIT FLASH 100-LQFP
• Manufacturer: Infineon Technologies
• Series: XE16xr

Specifications of SAF-XE164G-24F66L AC

• Core Processor: C166SV2
• Core Size: 16-Bit
• Speed: 66MHz
• Connectivity: CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
• Peripherals: I²S, POR, PWM, WDT
• Number Of I /o: 75
• Program Memory Size: 192KB (192K x 8)
• Program Memory Type: FLASH
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: SP000363795

Table 12
Parameter
External Pin Load
Capacitance
Voltage Regulator Buffer
Capacitance for DMP_M
Voltage Regulator Buffer
Capacitance for DMP_1
Operating frequency
Ambient temperature
1) If both core power domains are clocked, the difference between the power supply voltages must be less than
2) Performance of pad drivers, A/D Converter, and Flash module depends on
3) Overload conditions occur if the standard operating conditions are exceeded, i.e. the voltage on any pin
4) Not subject to production test - verified by design/characterization.
5) An overload current (
6) The timing is valid for pin drivers operating in default current mode (selected after reset). Reducing the output
7) To ensure the stability of the voltage regulators the EVRs must be buffered with ceramic capacitors. Separate
8) The operating frequency range may be reduced for specific types of the
Data Sheet
10 mV. This condition imposes additional constraints when using external power supplies.
Do not combine internal and external supply of different core power domains.
Do not supply the core power domains with two independent external voltage regulators. The simplest method
is to supply both power domains directly via a single external power supply.
If the external supply voltage
generated. Otherwise, the core supply voltage
parasitic effects.
This power reset can be generated by the on-chip SWD. If the SWD is disabled the power reset must be
generated by activating the PORST input.
exceeds the specified range:
overload currents on all pins may not exceed 50 mA. The supply voltages must remain within the specified
limits. Proper operation under overload conditions depends on the application.
Overload conditions must not occur on pin XTAL1 (powered by
adds to that pin’s leakage current (
defined by the overload coupling factor
polarity of the overload current that produces it.
The total current through a pin is |
voltage on analog inputs.
current may lead to increased delays or reduced driving capability (
buffer capacitors with the recomended values shall be connected as close as possible to each
the resistance of the board tracks below 2 Ω. Connect all
The minimum capacitance value is required for proper operation under all conditions (e.g. temperature).
Higher values slightly increase the startup time.
device designation (…FxxL). 80-MHz devices are marked …F80L.
Operating Condition Parameters (cont’d)
I
OV
) through a pin injects an error current (
V
DDP
V
Symbol
C
C
C
f
T
OV
SYS
I
A
L
EVRM
EVR1
TOT
I
becomes lower than the specified operating range, a power reset must be
OZ
>
| = |
). The value of the error current depends on the overload current and is
V
IHmax
K
I
OZ
OV
| + (|
. The polarity of the injected error current is reversed from the
(
Min.
–
1.0
0.47
–
–
I
OV
I
V
> 0) or
OV
DDI
69
| ×
may rise above its specified operating range due to
K
Values
Typ.
20
–
–
–
–
OV
V
V
). The additional error current may distort the input
OV
DDI1
<
pins together.
V
I
V
INJ
DDI
ILmin
Max.
–
4.7
2.2
80
–
) into the adjacent pins. This error current
C
).
L
XE166 Family Derivatives
).
(
I
OV
< 0). The absolute sum of input
XE164
V
DDP
Unit Note /
pF
µF
µF
MHz
°C
Electrical Parameters
.
. This is indicated in the
Test Condition
Pin drivers in
default mode
7)
One for each
supply pin
8)
See
Table 1
V2.1, 2008-08
V
DDI
XE164x
pin to keep
7)
6)