SAK-XC2364B-24F40L Infineon Technologies, SAK-XC2364B-24F40L Datasheet - Page 73

• Manufacturer Part Number: SAK-XC2364B-24F40L
• Description: IC MCU 16BIT FLASH 100-LQFP
• Manufacturer: Infineon Technologies
• Series: XC23xxBr

Specifications of SAK-XC2364B-24F40L

• Core Processor: C166SV2
• Core Size: 16/32-Bit
• Speed: 40MHz
• Connectivity: CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
• Peripherals: I²S, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Size: 192KB (192K x 8)
• Program Memory Type: FLASH
• Ram Size: 18K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-LSQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: SP000627180

Table 13
Parameter
Overload current coupling
factor for digital I/O pins
Absolute sum of overload
currents
Digital core supply voltage
Digital supply voltage for
IO pads and voltage
regulators
Digital ground voltage
1) To ensure the stability of the voltage regulators the EVRs must be buffered with ceramic capacitors. Separate
2) Use one Capacitor for each pin.
3) This is the reference load. For bigger capacitive loads, use the derating factors listed in the PAD properties
4) The timing is valid for pin drivers operating in default current mode (selected after reset). Reducing the output
5) The operating frequency range may be reduced for specific device types. This is indicated in the device
6) Overload conditions occur if the standard operating conditions are exceeded, i.e. the voltage on any pin
7) An overload current (
Data Sheet
buffer capacitors with the recomended values shall be connected as close as possible to each
the resistance of the board tracks below 2 Ohm. Connect all
value is required for proper operation under all conditions (e.g. temperature). Higher values slightly increase
the startup time.
section.
current may lead to increased delays or reduced driving capability (
designation (...FxxL). 80 MHz devices are marked ...F80L.
exceeds the specified range:
overload currents on all pins may not exceed 50 mA. The supply voltages must remain within the specified
limits. Proper operation under overload conditions depends on the application. Overload conditions must not
occur on pin XTAL1 (powered by
current adds to the respective pins leakage current (
current and is defined by the overload coupling factor
compared to the polarity of the overload current that produces it.The total current through a pin is |
+ (|
I
OV
|
K
OV
). The additional error current may distort the input voltage on analog inputs.
Operating Conditions (cont’d)
I
OV
) through a pin injects a certain error current (
V
OV
Symbol
K
CC
Σ|
SR
V
V
V
V
DDI
DDP
SS
OVD
I
>
DDI
OV
V
SR
).
SR 1.4
|
IHmax
SR 3.0
(
Min.
−
−
−
−
I
OV
XC2361B, XC2363B, XC2364B, XC2365B
> 0) or
73
I
OZ
K
). The amount of error current depends on the overload
OV
Values
Typ.
1.0 x
10
1.0 x
10
−
−
−
0
V
. The polarity of the injected error current is inverse
OV
-2
-4
V
<
DDI1
V
ILmin
XC2000 Family / Value Line
Max.
3.0 x
10
5.0 x
10
50
1.6
5.5
−
pins together. The minimum capacitance
C
L
).
((
-2
-3
I
I
INJ
OV
) into the adjacent pins. This error
< 0). The absolute sum of input
Unit Note /
-
-
mA
V
V
V
Electrical Parameters
Test Condition
I
subject to
production test
I
subject to
production test
not subject to
production test
OV
OV
< 0 mA; not
> 0 mA; not
V1.2, 2010-04
V
DDI
I
pin to keep
TOT
| = |
I
OZ
|