SAK-XC2287M-104F80L AA Infineon Technologies, SAK-XC2287M-104F80L AA Datasheet - Page 88

• Manufacturer Part Number: SAK-XC2287M-104F80L AA
• Description: IC MCU 32BIT FLASH 144-LQFP
• Manufacturer: Infineon Technologies
• Series: XC22xxMr

Specifications of SAK-XC2287M-104F80L AA

• Core Processor: C166SV2
• Core Size: 16/32-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
• Peripherals: I²S, POR, PWM, WDT
• Number Of I /o: 118
• Program Memory Size: 832KB (832K x 8)
• Program Memory Type: FLASH
• Ram Size: 50K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-LFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: SP000436560

Table 13
Parameter
Absolute sum of overload
currents
External Pin Load
Capacitance
Voltage Regulator Buffer
Capacitance for DMP_M
Voltage Regulator Buffer
Capacitance for DMP_1
Operating frequency
Ambient temperature
1) Performance of pad drivers, A/D Converter, and Flash module depends on
2) Overload conditions occur if the standard operating conditions are exceeded, i.e. the voltage on any pin
3) Not subject to production test - verified by design/characterization.
4) An overload current (
5) This is the reference load. For bigger capacitive loads, use the derating factors from
6) The timing is valid for pin drivers operating in default current mode (selected after reset). Reducing the output
7) To ensure the stability of the voltage regulators the EVRs must be buffered with ceramic capacitors. Separate
8) The operating frequency range may be reduced for specific types of the
Parameter Interpretation
The parameters listed in the following include both the characteristics of the XC228xM
and its demands on the system. To aid in correctly interpreting the parameters when
evaluating them for a design, they are marked accordingly in the column “Symbol”:
Data Sheet
exceeds the specified range:
overload currents on all pins may not exceed 50 mA. The supply voltages must remain within the specified
limits. Proper operation under overload conditions depends on the application.
Overload conditions must not occur on pin XTAL1 (powered by
adds to that pin’s leakage current (
defined by the overload coupling factor
polarity of the overload current that produces it.
The total current through a pin is |
voltage on analog inputs.
current may lead to increased delays or reduced driving capability (
buffer capacitors with the recomended values shall be connected as close as possible to each
the resistance of the board tracks below 2 Ω. Connect all
The minimum capacitance value is required for proper operation under all conditions (e.g. temperature).
Higher values slightly increase the startup time.
device designation (…FxxL). 80-MHz devices are marked …F80L.
Operating Condition Parameters (cont’d)
I
OV
) through a pin injects an error current (
V
Symbol
Σ|IOV|
C
C
C
f
T
OV
SYS
I
A
L
EVRM
EVR1
TOT
I
OZ
>
| = |
). The value of the error current depends on the overload current and is
V
IHmax
K
I
OZ
OV
| + (|
. The polarity of the injected error current is reversed from the
(
Min.
–
–
1.0
0.47
–
–
I
OV
I
> 0) or
OV
XC2000 Family Derivatives / Base Line
88
| ×
K
Values
Typ.
–
20
–
–
–
–
OV
V
V
). The additional error current may distort the input
5)
OV
DDI1
XC2287M, XC2286M, XC2285M
<
pins together.
V
I
V
INJ
DDIM
ILmin
Max.
50
–
4.7
2.2
80
–
) into the adjacent pins. This error current
C
L
).
).
(
I
OV
XC228xM
< 0). The absolute sum of input
V
DDP
Unit Note /
mA
pF
μF
μF
MHz
°C
Electrical Parameters
.
Section
. This is indicated in the
Test Condition
3)
Pin drivers in
default mode
7)
One for each
supply pin
8)
V2.0, 2009-03
V
4.6.4.
DDI
pin to keep
7)
6)