SAK-XC2287M-104F80L AA Infineon Technologies, SAK-XC2287M-104F80L AA Datasheet - Page 95

• Manufacturer Part Number: SAK-XC2287M-104F80L AA
• Description: IC MCU 32BIT FLASH 144-LQFP
• Manufacturer: Infineon Technologies
• Series: XC22xxMr

Specifications of SAK-XC2287M-104F80L AA

• Core Processor: C166SV2
• Core Size: 16/32-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, I²C, LIN, SPI, SSC, UART/USART, USI
• Peripherals: I²S, POR, PWM, WDT
• Number Of I /o: 118
• Program Memory Size: 832KB (832K x 8)
• Program Memory Type: FLASH
• Ram Size: 50K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 24x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-LFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: SP000436560

1) Not subject to production test - verified by design/characterization. Hysteresis is implemented to avoid
2) The maximum deliverable output current of a port driver depends on the selected output driver mode, see
3) As a rule, with decreasing output current the output levels approach the respective supply level (
4) This specification is not valid for outputs which are switched to open drain mode. In this case the respective
5) An additional error current (
6) The given values are worst-case values. In production test, this leakage current is only tested at 125°C; other
7) Keep current: Limit the current through this pin to the indicated value so that the enabled pull device can keep
8) Not subject to production test - verified by design/characterization.
Data Sheet
metastable states and switching due to internal ground bounce. It cannot suppress switching due to external
system noise under all conditions.
Section
V
output will float and the voltage is determined by the external circuit.
the definition of the overload coupling factor
The leakage current value is not tested in the lower voltage range but only in the upper voltage range. This
parameter is ensured by correlation.
values are ensured by correlation. For derating, please refer to the following descriptions:
Leakage derating depending on temperature (
I
Leakage derating depending on voltage level (DV =
I
This voltage derating formula is an approximation which applies for maximum temperature.
Because pin P2.8 is connected to two pads (standard pad and high-speed clock pad), it has twice the normal
leakage.
the default pin level:
Force current: Drive the indicated minimum current through this pin to change the default pin level driven by
the enabled pull device:
These values apply to the fixed pull-devices in dedicated pins and to the user-selectable pull-devices in
general purpose IO pins.
Because pin P2.8 is connected to two pads (standard pad and high-speed clock pad), it has twice the normal
capacitance.
OZ
OZ
OH
= 0.03 × e
=
→
I
V
OZtempmax
DDP
4.6.4. The limit for pin groups must be respected.
). However, only the levels for nominal output currents are verified.
(1.35 + 0.028×TJ)
- (1.3 × DV) [μA]
V
PIN
V
≥
[μA]. For example, at a temperature of 95°C the resulting leakage current is 1.65 μA.
PIN
V
I
INJ
IH
≤
) will flow if an overload current flows through an adjacent pin. Please refer to
for a pullup;
V
IL
for a pullup;
V
K
PIN
OV
T
V
J
≤
.
PIN
= junction temperature [°C]):
XC2000 Family Derivatives / Base Line
V
95
IL
≥
V
for a pulldown.
V
DDP
IH
for a pulldown.
-
V
PIN
XC2287M, XC2286M, XC2285M
[V]):
Electrical Parameters
V2.0, 2009-03
V
OL
→
V
SS
,