AT90S4433-8PC Atmel, AT90S4433-8PC Datasheet - Page 88
![IC MCU 4K FLSH 8MHZ A/D 28DIP](/photos/7/21/72189/453-28-dip_sml.jpg)
AT90S4433-8PC
Manufacturer Part Number
AT90S4433-8PC
Description
IC MCU 4K FLSH 8MHZ A/D 28DIP
Manufacturer
Atmel
Series
AVR® 90Sr
Datasheet
1.AT90S4433-8AC.pdf
(126 pages)
Specifications of AT90S4433-8PC
Core Processor
AVR
Core Size
8-Bit
Speed
8MHz
Connectivity
SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
20
Program Memory Size
4KB (2K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
128 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 6x10b
Oscillator Type
External
Operating Temperature
0°C ~ 70°C
Package / Case
28-DIP (0.300", 7.62mm)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT90S4433-8PC
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Chip Erase
Programming the Flash
88
AT90S/LS4433
The Chip Erase command will erase the Flash and EEPROM memories and the Lock
bits. The Lock bits are not reset until the Flash and EEPROM have been completely
erased. The Fuse bits are not changed. Chip Erase must be performed before the Flash
or EEPROM is reprogrammed.
A: Load Command “Chip Erase”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS to “0”.
3. Set DATA to “1000 0000”. This is the command for Chip Erase.
4. Give XTAL1 a positive pulse. This loads the command.
5. Give WR a t
A: Load Command “Write Flash”
1. Set XA1, XA0 to “10”. This enables command loading.
2. Set BS to “0”.
3. Set DATA to “0001 0000”. This is the command for Write Flash.
4. Give XTAL1 a positive pulse. This loads the command.
B: Load Address High Byte
1. Set XA1, XA0 to “00”. This enables address loading.
2. Set BS to “1”. This selects High Byte.
3. Set DATA = Address High Byte ($00 - $07).
4. Give XTAL1 a positive pulse. This loads the address High Byte.
C: Load Address Low Byte
1. Set XA1, XA0 to “00”. This enables address loading.
2. Set BS to “0”. This selects Low Byte.
3. Set DATA = Address Low Byte ($00 - $FF).
4. Give XTAL1 a positive pulse. This loads the address Low Byte.
D: Load Data Low Byte
1. Set XA1, XA0 to “01”. This enables data loading.
2. Set DATA = Data Low Byte ($00 - $FF).
3. Give XTAL1 a positive pulse. This loads the data Low Byte.
E: Write Data Low Byte
1. Set BS to “0”. This selects low data.
2. Give WR a negative pulse. This starts programming of the data byte. RDY/BSY
3. Wait until RDY/BSY goes high to program the next byte.
(See Figure 63 for signal waveforms.)
F: Load Data High Byte
1. Set XA1, XA0 to “01”. This enables data loading.
2. Set DATA = Data High Byte ($00 - $FF).
3. Give XTAL1 a positive pulse. This loads the data High Byte.
t
goes low.
WLWH_CE
value. Chip Erase does not generate any activity on the RDY/BSY pin.
WLWH_CE
wide negative pulse to execute Chip Erase. See Table 33 for
1042H–AVR–04/03