PIC18C242-E/SO Microchip Technology, PIC18C242-E/SO Datasheet - Page 124

• Manufacturer Part Number: PIC18C242-E/SO
• Description: IC MCU OTP 8KX16 A/D 28SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Cr

Specifications of PIC18C242-E/SO

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: OTP
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 28-SOIC (7.5mm Width)
• Processor Series: PIC18C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: MSSP, SPI, I2C, USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 23
• Number Of Timers: 1 x 16 bit
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: ICE2000, DM163022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 5 bit
• For Use With: I3DB18C452 - BOARD DAUGHTER ICEPIC3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18C242E/SO

PIC18CXX2
When the application software is expecting to receive
valid data, the SSPBUF should be read before the next
byte of data to transfer is written to the SSPBUF. Buffer
full bit, BF (SSPSTAT<0>), indicates when SSPBUF
has been loaded with the received data (transmission
is complete). When the SSPBUF is read, the BF bit is
cleared. This data may be irrelevant if the SPI is only a
EXAMPLE 14-1:
The SSPSR is not directly readable or writable, and
can only be accessed by addressing the SSPBUF reg-
ister. Additionally, the MSSP status register (SSPSTAT)
indicates the various status conditions.
14.3.2
To enable the serial port, SSP enable bit, SSPEN
(SSPCON1<5>), must be set. To reset or reconfigure
SPI mode, clear the SSPEN bit, re-initialize the
SSPCON registers, and then set the SSPEN bit. This
configures the SDI, SDO, SCK, and SS pins as serial
DS39026C-page 122
LOOP BTFSS SSPSTAT, BF
GOTO
MOVF
MOVWF RXDATA
MOVF
MOVWF SSPBUF
ENABLING SPI I/O
LOOP
SSPBUF, W
TXDATA, W
LOADING THE SSPBUF (SSPSR) REGISTER
;Has data been received(transmit complete)?
;No
;WREG reg = contents of SSPBUF
;Save in user RAM, if data is meaningful
;W reg = contents of TXDATA
;New data to xmit
transmitter. Generally the MSSP Interrupt is used to
determine when the transmission/reception has com-
pleted. The SSPBUF must be read and/or written. If the
interrupt method is not going to be used, then software
polling can be done to ensure that a write collision does
not occur. Example 14-1 shows the loading of the
SSPBUF (SSPSR) for data transmission.
port pins. For the pins to behave as the serial port func-
tion, some must have their data direction bits (in the
TRIS register) appropriately programmed. That is:
• SDI is automatically controlled by the SPI module
• SDO must have TRISC<5> bit cleared
• SCK (Master mode) must have TRISC<3> bit cleared
• SCK (Slave mode) must have TRISC<3> bit set
• SS must have TRISC<4> bit set
Any serial port function that is not desired may be over-
ridden by programming the corresponding data direc-
tion (TRIS) register to the opposite value.
2001 Microchip Technology Inc.