DSPIC30F4013T-20I/ML Microchip Technology, DSPIC30F4013T-20I/ML Datasheet - Page 143

• Manufacturer Part Number: DSPIC30F4013T-20I/ML
• Description: IC DSPIC MCU/DSP 48K 44QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F4013T-20I/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: AC'97, Brown-out Detect/Reset, I²S, POR, PWM, WDT
• Number Of I /o: 30
• Program Memory Size: 48KB (16K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: DSPIC30F4013T20IM

20.4
The
between various kinds of Reset:
a)
b)
c)
d)
e)
f)
g)
h)
FIGURE 20-2:
20.4.1
A power-on event will generate an internal POR pulse
when a V
at the POR circuit threshold voltage (V
nominally 1.85V. The device supply voltage character-
istics must meet specified starting voltage and rise rate
requirements. The POR pulse will reset a POR timer
and place the device in the Reset state. The POR also
selects the device clock source identified by the oscil-
lator configuration fuses.
 2004 Microchip Technology Inc.
Power-on Reset (POR)
MCLR Reset during normal operation
MCLR Reset during Sleep
Watchdog Timer (WDT) Reset (during normal
operation)
Programmable Brown-out Reset (BOR)
RESET Instruction
Reset caused by trap lockup (TRAPR)
Reset caused by illegal opcode or by using an
uninitialized W register as an address pointer
(IOPUWR)
MCLR
V
DD
PIC18F2220/2320/4220/4320
Reset
DD
Instruction
POR: POWER-ON RESET
RESET
rise is detected. The Reset pulse will occur
Trap Conflict
Illegal Opcode/
Uninitialized W Register
Brown-out
V
Sleep or Idle
Module
Detect
DD
WDT
Reset
RESET SYSTEM BLOCK DIAGRAM
Rise
BOREN
Glitch Filter
Digital
POR
POR
differentiates
Advance Information
) which is
BOR
Different registers are affected in different ways by var-
ious Reset conditions. Most registers are not affected
by a WDT wake-up since this is viewed as the resump-
tion of normal operation. Status bits from the RCON
register are set or cleared differently in different Reset
situations, as indicated in Table 20-4. These bits are
used in software to determine the nature of the Reset.
A block diagram of the On-Chip Reset Circuit is shown
in Figure 20-2.
A MCLR noise filter is provided in the MCLR Reset
path. The filter detects and ignores small pulses.
Internally generated Resets do not drive MCLR pin low.
The POR circuit inserts a small delay, T
nominally 10 µs and ensures that the device bias cir-
cuits are stable. Furthermore, a user selected power-
up time-out (T
is based on device configuration bits and can be 0 ms
(no delay), 4 ms, 16 ms, or 64 ms. The total delay is at
device power-up, T
have expired, SYSRST will be negated on the next
leading edge of the Q1 clock and the PC will jump to the
Reset vector.
The timing for the SYSRST signal is shown in
Figure 20-3 through Figure 20-5.
dsPIC30F3014/4013
PWRT
) is applied. The T
POR
S
R
+ T
PWRT
Q
. When these delays
DS70138C-page 141
PWRT
SYSRST
POR
parameter
, which is