AT90USB1287-16AUR Atmel, AT90USB1287-16AUR Datasheet - Page 283

• Manufacturer Part Number: AT90USB1287-16AUR
• Description: IC MCU AVR 128K ISP USB TQFP64
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB1287-16AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART, USB, USB OTG
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 48
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7593K–AVR–11/09
• 7-6 - Reserved
The value read from these bits is always 0. Do not set these bits.
• 5 - STALLRQ - STALL Request Handshake Bit
Set to request a STALL answer to the host for the next handshake.
Cleared by hardware when a new SETUP is received. Clearing by software has no effect.
See Section 22.11, page 271 for more details.
• 4 - STALLRQC - STALL Request Clear Handshake Bit
Set to disable the STALL handshake mechanism.
Cleared by hardware immediately after the set. Clearing by software has no effect.
See Section 22.11, page 271 for more details.
3
• RSTDT - Reset Data Toggle Bit
Set to automatically clear the data toggle sequence:
For OUT endpoint: the next received packet will have the data toggle 0.
For IN endpoint: the next packet to be sent will have the data toggle 0.
Cleared by hardware instantaneously. The firmware does not have to wait that the bit is cleared.
Clearing by software has no effect.
• 2 - Reserved
The value read from these bits is always 0. Do not set these bits.
• 1 - Reserved
The value read from these bits is always 0. Do not set these bits.
• 0 - EPEN - Endpoint Enable Bit
Set to enable the endpoint according to the device configuration. Endpoint 0 shall always be
enabled after a hardware or USB reset and participate in the device configuration.
Clear this bit to disable the endpoint. See Section 22.6, page 268 for more details.
• 7-6 - EPTYPE1:0 - Endpoint Type Bits
Set this bit according to the endpoint configuration:
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
R/W
R
7
0
7
0
-
EPTYPE1:0
R/W
R
6
0
-
6
0
STALLRQ
W
5
0
R
5
0
-
STALLRQC
R
W
4
0
-
4
0
RSTDT
R
3
0
-
W
3
0
R
2
0
-
AT90USB64/128
2
R
0
-
R
1
0
-
R
1
0
-
EPDIR
R/W
EPEN
R/W
0
0
0
0
UECFG0X
UECONX
283