C8051F019 Silicon Laboratories Inc, C8051F019 Datasheet - Page 68
![IC 8051 MCU 16K FLASH 48TQFP](/photos/15/92/159280/tqfp-48_sml.jpg)
C8051F019
Manufacturer Part Number
C8051F019
Description
IC 8051 MCU 16K FLASH 48TQFP
Manufacturer
Silicon Laboratories Inc
Series
C8051F018r
Specifications of C8051F019
Core Processor
8051
Core Size
8-Bit
Speed
25MHz
Connectivity
SMBus (2-Wire/I²C), SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
16
Program Memory Size
16KB (16K x 8)
Program Memory Type
FLASH
Ram Size
1.25K x 8
Voltage - Supply (vcc/vdd)
2.8 V ~ 3.6 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TQFP, 48-VQFP
Data Bus Width
8 bit
Data Ram Size
1.25 KB
Interface Type
I2C, SMBus, SPI, UART
Maximum Clock Frequency
25 MHz
Number Of Programmable I/os
16
Number Of Timers
16 bit
Operating Supply Voltage
2.8 V to 3.6 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 8 Channel
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Eeprom Size
-
Lead Free Status / Rohs Status
No
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
C8051F019
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F019-GQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F019-GQR
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
Company:
Part Number:
C8051F019R
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode. The
Missing Clock Detector should be disabled if the CPU is to be put to sleep for longer than the MCD timeout of
100sec.
Bit7:
Bits6-2: GF4-GF0: General Purpose Flags 4-0.
Bit1:
Bit0:
SMOD
R/W
Bit7
SMOD: Serial Port Baud Rate Doubler Enable.
0: Serial Port baud rate is that defined by Serial Port Mode in SCON.
1: Serial Port baud rate is double that defined by Serial Port Mode in SCON.
These are general purpose flags for use under software control.
Setting this bit will place the CIP-51 in Stop mode. This bit will always be read as 0.
1: Goes into power down mode. (Turns off internal oscillator).
Setting this bit will place the CIP-51 in Idle mode. This bit will always be read as 0.
1: Goes into idle mode. (Shuts off clock to CPU, but clock to Timers, Interrupts, Serial
STOP: Stop Mode Select.
IDLE: Idle Mode Select.
Ports, and Analog Peripherals are still active.)
GF4
R/W
Bit6
R/W
GF3
Bit5
Figure 8.15. PCON: Power Control Register
R/W
GF2
Bit4
Rev. 1.2
GF1
R/W
Bit3
R/W
GF0
Bit2
STOP
R/W
Bit1
C8051F018
C8051F019
IDLE
R/W
Bit0
SFR Address:
Reset Value
00000000
0x87
68