MC9S08DN32ACLH Freescale Semiconductor, MC9S08DN32ACLH Datasheet - Page 268

• Manufacturer Part Number: MC9S08DN32ACLH
• Description: IC MCU 32K FLASH 1.5K RAM 64LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08DN32ACLH

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: S08DN
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: I2C, SCI, SPI
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08DZ60
• On-chip Adc: 12 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 15 Timer/PWM Module (S08TPMV3)
15.3
This section consists of register descriptions in address order.
15.3.1
TPMxSC contains the overflow status flag and control bits used to configure the interrupt enable, TPM
configuration, clock source, and prescale factor. These controls relate to all channels within this timer
module.
268
CLKS[B:A]
Reset
CPWMS
PS[2:0]
Field
TOIE
TOF
4–3
2–0
W
7
6
5
R
Register Definition
TOF
Timer overflow flag. This read/write flag is set when the TPM counter resets to 0x0000 after reaching the modulo
value programmed in the TPM counter modulo registers. Clear TOF by reading the TPM status and control
register when TOF is set and then writing a logic 0 to TOF. If another TPM overflow occurs before the clearing
sequence is complete, the sequence is reset so TOF would remain set after the clear sequence was completed
for the earlier TOF. This is done so a TOF interrupt request cannot be lost during the clearing sequence for a
previous TOF. Reset clears TOF. Writing a logic 1 to TOF has no effect.
0 TPM counter has not reached modulo value or overflow
1 TPM counter has overflowed
Timer overflow interrupt enable. This read/write bit enables TPM overflow interrupts. If TOIE is set, an interrupt is
generated when TOF equals one. Reset clears TOIE.
0 TOF interrupts inhibited (use for software polling)
1 TOF interrupts enabled
Center-aligned PWM select. When present, this read/write bit selects CPWM operating mode. By default, the
TPM operates in up-counting mode for input capture, output compare, and edge-aligned PWM functions. Setting
CPWMS reconfigures the TPM to operate in up/down counting mode for CPWM functions. Reset clears CPWMS.
0 All channels operate as input capture, output compare, or edge-aligned PWM mode as selected by the
1 All channels operate in center-aligned PWM mode.
Clock source selects. As shown in
three clock sources to drive the counter prescaler. The fixed system clock source is only meaningful in systems
with a PLL-based or FLL-based system clock. When there is no PLL or FLL, the fixed-system clock source is the
same as the bus rate clock. The external source is synchronized to the bus clock by TPM module, and the fixed
system clock source (when a PLL or FLL is present) is synchronized to the bus clock by an on-chip
synchronization circuit. When a PLL or FLL is present but not enabled, the fixed-system clock source is the same
as the bus-rate clock.
Prescale factor select. This 3-bit field selects one of 8 division factors for the TPM clock input as shown in
Table
the clock source selected to drive the TPM system. The new prescale factor will affect the clock source on the
next system clock cycle after the new value is updated into the register bits.
TPM Status and Control Register (TPMxSC)
0
0
7
MSnB:MSnA control bits in each channel’s status and control register.
15-4. This prescaler is located after any clock source synchronization or clock source selection so it affects
TOIE
0
6
Figure 15-7. TPM Status and Control Register (TPMxSC)
Table 15-2. TPMxSC Field Descriptions
CPWMS
MC9S08DN60 Series Data Sheet, Rev 3
5
0
Table
15-3, this 2-bit field is used to disable the TPM system or select one of
CLKSB
0
4
Description
CLKSA
0
3
PS2
0
2
PS1
Freescale Semiconductor
1
0
PS0
0
0