MCP6V06T-E/MNY Microchip Technology, MCP6V06T-E/MNY Datasheet
MCP6V06T-E/MNY
Specifications of MCP6V06T-E/MNY
Available stocks
Related parts for MCP6V06T-E/MNY
MCP6V06T-E/MNY Summary of contents
Page 1
... PSRR and CMRR. These products operate with a single supply voltage as low as 1.8V, while drawing 300 µA/amplifier (typical) of quiescent current. The Microchip Technology Inc. MCP6V06/7/8 op amps are offered in single (MCP6V06), single with Chip Select (CS) (MCP6V08), and dual (MCP6V07). They are designed in an advanced CMOS process. ...
Page 2
... MCP6V06/7/8 Typical Application Circuit kΩ MCP6V06 Offset Voltage Correction for Power Driver DS22093B-page OUT MCP6XXX © 2008 Microchip Technology Inc. ...
Page 3
... TC 2: Figure 2-18 shows how V CMR © 2008 Microchip Technology Inc. † Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of +1 ...
Page 4
... G = +2, 0.5V input overdrive 1. 5. µ GND / and Figure 1-6). Conditions tone = kHz 1. tone = kHz 5. within 50 µV of its final value step of 2V, IN within 50 µV of its final value /2, DD 90% point (Note 2) OUT and Figure 2-38 show both an IMD © 2008 Microchip Technology Inc. ...
Page 5
... Thermal Resistance, 8L-SOIC Note 1: Operation must not cause T to exceed Maximum Junction Temperature specification (150°C Measured on a standard JC51-7, four layer printed circuit board with ground plane and vias. © 2008 Microchip Technology Inc. = +25° +1.8V to +5.5V pF, and CS = GND (refer to ...
Page 6
... DC). The op amp’s common REF = V /2. The error at the CM IN with a noise gain of OUT 20.0 kΩ 50Ω 0.1% 25 turn V REF µ ISO OUT 100 nF MCP6V0X V L 24.9 Ω 20.0 kΩ 0.1% Test Circuit for Dynamic © 2008 Microchip Technology Inc. ...
Page 7
... Soldered on PCB 20% 15% 10 Input Offset Voltage's Quadratic Temp Co (nV/° FIGURE 2-3: Input Offset Voltage Quadratic Temp Co. © 2008 Microchip Technology Inc. = +1.8V to 5.5V GND 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 FIGURE 2-4: ...
Page 8
... FIGURE 2-11: 160 155 V 150 V 145 140 135 130 125 120 -50 FIGURE 2-12: Ambient Temperature / / OUT DD 1/PSRR (µV/V) PSRR 5. 1.8V DD 1/A (µV/ Open-Loop Gain 1.8V DD CMRR PSRR - 100 125 Ambient Temperature (°C) CMRR and PSRR vs. © 2008 Microchip Technology Inc. ...
Page 9
... -200 -400 Common Mode Input Voltage (V) FIGURE 2-15: Input Bias and Offset Currents vs. Common Mode Input Voltage with T = +125°C. A © 2008 Microchip Technology Inc. = +1.8V to 5.5V GND 10,000 V = 5.5V DD 1,000 -I 100 10 1 100 125 105 115 125 FIGURE 2-16: Currents vs ...
Page 10
... Power Supply Voltage (V) Output Short Circuit Current +125°C +85°C +25°C -40°C Power Supply Voltage (V) Supply Current vs. Power = +25°C POR Trip Voltage (V) Power On Reset Trip © 2008 Microchip Technology Inc. ...
Page 11
... Note: Unless otherwise indicated +25° / kΩ pF, and CS = GND 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -50 - Ambient Temperature (°C) FIGURE 2-24: Power On Reset Voltage vs. Ambient Temperature. © 2008 Microchip Technology Inc. = +1.8V to 5.5V GND 100 125 MCP6V06 OUT DD DS22093B-page 11 ...
Page 12
... V = 5.5V GBWP DD 110 100 1. - 100 125 Ambient Temperature (°C) Gain Bandwidth Product 130 120 110 100 Common Mode Input Voltage (V) Gain Bandwidth Product 130 120 110 100 Output Voltage (V) Gain Bandwidth Product © 2008 Microchip Technology Inc. ...
Page 13
... DD 1.E+03 1k 100 1.E+ V/V 10 1.E+ V 100 V/V 1 1.E+00 100k 1M 10M 1.0E+05 1.0E+06 1.0E+07 Frequency (Hz) FIGURE 2-32: Closed-Loop Output Impedance vs. Frequency with V DD © 2008 Microchip Technology Inc. = +1.8V to 5.5V GND 100 100M 100k 1.0E+08 1.E+05 FIGURE 2-33: = 1.8V. Separation vs. Frequency ...
Page 14
... kHz V = 5.5V DD tone 10k 100k 1.E+03 1.E+04 1.E+05 Frequency (Hz) Inter-Modulation Distortion Disturbance (see DD NPBW = 10 Hz NPBW = 100 t (s) Input Noise vs. Time with =1.8V. DD NPBW = 10 Hz NPBW = 100 t (s) Input Noise vs. Time with =5.5V. DD © 2008 Microchip Technology Inc. ...
Page 15
... Time (200 µs/div) FIGURE 2-42: Input Offset Voltage vs. Time at Power Up OUT Time (ms) FIGURE 2-43: The MCP6V06/7/8 family shows no input phase reversal with overdrive. © 2008 Microchip Technology Inc. = +1.8V to 5.5V GND -10 - FIGURE 2-44: Step Response. 5.5 5.0 5.0 4.5 4.5 4.0 4 ...
Page 16
... ODR 100 125 FIGURE 2-50: Time vs. Inverting Gain / / OUT OUT 5.5V OUT -100 V/V 0 0.5V Overdrive -1 Time (50 µs/div) Output Overdrive Recovery low ODR 10 100 1000 Inverting Gain Magnitude (V/V) Output Overdrive Recovery © 2008 Microchip Technology Inc. ...
Page 17
... Hysteresis 100 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Chip Select Voltage (V) FIGURE 2-53: Power Supply Current vs. Chip Select Voltage with V = 5.5V. DD © 2008 Microchip Technology Inc. = +25° +1.8V to 5.5V 1 5.5V 0.9 DD 0.8 0.7 ...
Page 18
... FIGURE 2-61: Shutdown vs. Power Supply Voltage. 75 100 125 = OUT 100 125 Ambient Temperature (°C) Chip Select’s Pull-down ) vs. Ambient Temperature. DD +125°C +85°C +25°C -40°C Power Supply Voltage (V) Quiescent Current in © 2008 Microchip Technology Inc. ...
Page 19
... SS operation, the other pins are between V Typically, these parts are used in a single (positive) supply configuration. In this case ground and V is connected to the supply need bypass capacitors. © 2008 Microchip Technology Inc. 3-1. MCP6V08 Symbol TDFN SOIC ...
Page 20
... MCP6V06/7/8 NOTES: DS22093B-page 20 © 2008 Microchip Technology Inc. ...
Page 21
... The clock is derived from an internal R-C oscillator running at a rate 650 kHz. The oscillator’s OSC1 output is divided down to the desired rate also randomized to minimize (spread) undesired clock tones in the output. © 2008 Microchip Technology Inc. MCP6V06/7/8 4.1 Overview of Auto-zeroing Operation Figure 4-1 shows a simplified diagram of the MCP6V06/7/8 auto-zeroed op amps ...
Page 22
... IMD distortion tones are generated about all of the square wave clock’s harmonics. See Figure 2-37 and ) and very low offset OL Output V OUT Buffer /ΔT ), 1/f noise, and input offset OS A Output V OUT Buffer Figure 2-38. © 2008 Microchip Technology Inc. ...
Page 23
... IN resistors R and R limit the possible current drawn out the input pins. Diodes D and D prevent the input 1 2 © 2008 Microchip Technology Inc. pins (V + and V IN dump any currents onto V shown, resistors R through D and – in nor- IN ...
Page 24
... FIGURE 4-7: for Capacitive Loads. in Figure 4-6) ISO R ISO V OUT C L MCP6V0X Output Resistor ISO values for ISO G < 10p 100p 1n 10n 100n 1.E-11 1.E-10 1.E-09 1.E-08 1.E-07 C (F) L Recommended R values ISO © 2008 Microchip Technology Inc. ...
Page 25
... C F 0.1 µF FIGURE 4-9: One Solution To Output Load Issue. © 2008 Microchip Technology Inc. 4.3.7 REDUCING UNDESIRED NOISE AND SIGNALS Reduce undesired noise and signals with: • Low bandwidth signal filters: - Minimizes random analog noise - Reduces interfering signals • ...
Page 26
... P M magnitude V is neglected MCP6V06 FIGURE 4-11: PCB Layout and Schematic for Single Non-inverting and Inverting Amplifiers. Note: Changing the orientation of the resistors will usually cause a significant decrease in the cancellation of the thermal voltages. © 2008 Microchip Technology Inc. V OUT V OUT ...
Page 27
... PCB Layout and Schematic for Single Difference Amplifier. Note: Changing the orientation of the resistors will usually cause a significant decrease in the cancellation of the thermal voltages. © 2008 Microchip Technology Inc. 4.3.9.4 Dual Non-inverting Amplifier Layout for Thermo-junctions The dual op amp amplifiers shown in and ...
Page 28
... Use more appropriate capacitor types in the signal path and minimize mechanical stresses and vibration. Humidity can cause electro-chemical potential voltages to appear in a circuit. Proper PCB cleaning helps, as does the use of encapsulants. © 2008 Microchip Technology Inc. ...
Page 29
... FIGURE 4-16: High Performance Design. © 2008 Microchip Technology Inc. 4.4.2 RTD SENSOR The ratiometric circuit in wire RTD. It corrects for the sensor’s wiring resistance by subtracting the voltage across the middle R top R1 does not change the output voltage; it balances the op amp inputs ...
Page 30
... would produce a Theve 1.00V and 250(R ). The TH resistor (in Figure 4-18), producing the ® can be used and C integrate 2 2 and OUT MCP6XXX 3 kΩ MCP6V06 Offset Correction. correction circuitry does OS MCP6V06 kΩ OUT MCP6541 Precision Comparator. © 2008 Microchip Technology Inc. ...
Page 31
... Helpful links are also provided for Data sheets, Purchase and Sampling of Microchip parts. © 2008 Microchip Technology Inc. MCP6V06/7/8 5.5 Analog Demonstration and Evaluation Boards ...
Page 32
... DS22093B-page 32 Example E/MD^^ Example MCP6VO6E SN Example: Device Code MCP6V06 AAC MCP6V08 AAD Note: Applies to 8-Lead 2x3 TDFN 6V07 e 3 0823 256 : e 3 0823 256 AAC 838 © 2008 Microchip Technology Inc. ...
Page 33
... NOTE 1 TOP VIEW A3 © 2008 Microchip Technology Inc. MCP6V06/7 EXPOSED PAD 2 D2 BOTTOM VIEW A A1 NOTE NOTE 1 DS22093B-page 33 ...
Page 34
... MCP6V06/7/8 N NOTE DS22093B-page φ α c β © 2008 Microchip Technology Inc. ...
Page 35
... Microchip Technology Inc. MCP6V06/7/8 DS22093B-page 35 ...
Page 36
... MCP6V06/7/8 DS22093B-page 36 © 2008 Microchip Technology Inc. ...
Page 37
... Microchip Technology Inc. MCP6V06/7/8 DS22093B-page 37 ...
Page 38
... MCP6V06/7/8 NOTES: DS22093B-page 38 © 2008 Microchip Technology Inc. ...
Page 39
... Added information on the Exposed Thermal Pad (EP) for the 8-lead, 2x3 TDFN and 8-lead, 4x4 DFN packages. 4. Added Section 4.3.6 “Stabilizing Loads”. 5. Other minor typographical corrections. Revision A (June 2008) • Original Release of this Document. © 2008 Microchip Technology Inc. Output MCP6V06/7/8 DS22093B-page 39 ...
Page 40
... CMRR 106 — 1.8V CMRR 116 — 5.5V 114 — 1.8V 122 — 5.5V Table B-1. = GND / 1-6). Conditions = -0.2V to 2.0V (Note -0.2V to 5.7V (Note 0.2V to 1.6V (Note 1) OUT = 0.2V to 5.3V (Note 1) OUT © 2008 Microchip Technology Inc. ...
Page 41
... Device Temperature Package Range Device: MCP6V06 Single Op Amp MCP6V06T Single Op Amp (Tape and Reel for 2x3 TDFN and SOIC) MCP6V07 Dual Op Amp MCP6V07T Dual Op Amp (Tape and Reel for 4×4 DFN and SOIC) MCP6V08 Single Op Amp with Chip Select MCP6V08T Single Op Amp with Chip Select ...
Page 42
... MCP6V06/7/8 NOTES: DS22093B-page 42 © 2008 Microchip Technology Inc. ...
Page 43
... PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 44
... Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2008 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...