HCPL-7800-000E Avago Technologies US Inc., HCPL-7800-000E Datasheet - Page 14

• Manufacturer Part Number: HCPL-7800-000E
• Description: OPTOCOUPLER AMP 100KHZ 8-DIP
• Manufacturer: Avago Technologies US Inc.
• Type: General Purposer

Specifications of HCPL-7800-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Amplifier Type: Isolation
• Number Of Circuits: 1
• -3db Bandwidth: 100kHz
• Current - Input Bias: 500nA
• Voltage - Input Offset: 300µV
• Current - Supply: 10.9mA
• Current - Output / Channel: 16mA
• Voltage - Supply, Single/dual (±): 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Number Of Channels: Single
• Common Mode Rejection Ratio (min): 76 dB
• Available Set Gain: 18.31 dB
• Input Offset Voltage: 2 mV
• Operating Supply Voltage: 5 V
• Supply Current: 16 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Bandwidth: 100 kHz
• Common Mode Rejection Ratio: 76
• Current, Supply: 10.86 mA (Input), 11.56 mA (Output)
• Package Type: DIP-8
• Power Dissipation: 600 mW
• Propagation Delay: 4.99 μs
• Slew Rate: 10
• Temperature, Operating, Range: -40 to +85 °C
• Time, Fall: 2.96 μs
• Time, Rise: 2.96 μs
• Voltage, Gain: 8 V/V
• Voltage, Input: 2 V
• Voltage, Input Offset: 0.3 mV
• Voltage, Noise: 31.5 mV
• Voltage, Supply: 5.5 V
• No. Of Channels: 1
• Isolation Voltage: 3.75kV
• Optocoupler Output Type: Analog
• Input Current: 16mA
• Output Voltage: 3.8V
• Opto Case Style: DIP
• No. Of Pins: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Slew Rate: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 516-1481-5

As shown in Figure 18, 0.1 µF bypass capacitors (C1, C2)
should be located as close as possible to the pins of the
HCPL-7800(A). The bypass capacitors are required because
of the high-speed digital nature of the signals inside the
HCPL-7800(A). A 0.01 µF bypass capacitor (C2) is also rec-
ommended at the input due to the switched-capacitor
nature of the input circuit. The input bypass capacitor
also forms part of the anti-aliasing filter, which is recom-
mended to prevent high-frequency noise from aliasing
down to lower frequencies and interfering with the input
signal. The input filter also performs an important reliabil-
ity function—it reduces transient spikes from ESD events
flowing through the current sensing resistor.
Figure 18: Recommended Application Circuit.
Figure 19. Example Printed Circuit Board Layout.

* * *
TO R
TO R
SENSE+
SENSE-
MOTOR
TO V
DD1
+
R
SENSE
R5
-
HV+
HV-
C3
C1
0.1
µF
C2
* * *
GATE DRIVE
FLOATING
POSITIVE
CIRCUIT
SUPPLY
IN
78L05
C4
U1
OUT
R5
68
TO V
V
V
OUT+
OUT-
DD2
C2
0.1
µF
* * *
0.01
µF
C3
1
2
3
4
HCPL-7800
PC Board Layout
The design of the printed circuit board (PCB) should follow
good layout practices, such as keeping bypass capacitors
close to the supply pins, keeping output signals away
from input signals, the use of ground and power planes,
etc. In addition, the layout of the PCB can also affect the
isolation transient immunity (CMTI) of the HCPL-7800(A),
due primarily to stray capacitive coupling between the
input and the output circuits. To obtain optimal CMTI
performance, the layout of the PC board should minimize
any stray coupling by maintaining the maximum possible
distance between the input and output sides of the circuit
and ensuring that any ground or power plane on the PC
board does not pass directly below or extend much wider
than the body of the HCPL-7800(A).
U2
8
7
6
5
+5 V
C4
0.1 µF
150 pF
2.00 K
2.00 K
C6
R1
R2
R4
10.0 K
-
+
+15 V
-15 V
U3
150 pF
10.0 K
MC34081
C5
R3
0.1 µF
C7
0.1 µF
C8
V OUT