HCPL-7800-000E Avago Technologies US Inc., HCPL-7800-000E Datasheet - Page 5

• Manufacturer Part Number: HCPL-7800-000E
• Description: OPTOCOUPLER AMP 100KHZ 8-DIP
• Manufacturer: Avago Technologies US Inc.
• Type: General Purposer

Specifications of HCPL-7800-000E

• Package / Case: 8-DIP (0.300", 7.62mm)
• Amplifier Type: Isolation
• Number Of Circuits: 1
• -3db Bandwidth: 100kHz
• Current - Input Bias: 500nA
• Voltage - Input Offset: 300µV
• Current - Supply: 10.9mA
• Current - Output / Channel: 16mA
• Voltage - Supply, Single/dual (±): 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Number Of Channels: Single
• Common Mode Rejection Ratio (min): 76 dB
• Available Set Gain: 18.31 dB
• Input Offset Voltage: 2 mV
• Operating Supply Voltage: 5 V
• Supply Current: 16 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Bandwidth: 100 kHz
• Common Mode Rejection Ratio: 76
• Current, Supply: 10.86 mA (Input), 11.56 mA (Output)
• Package Type: DIP-8
• Power Dissipation: 600 mW
• Propagation Delay: 4.99 μs
• Slew Rate: 10
• Temperature, Operating, Range: -40 to +85 °C
• Time, Fall: 2.96 μs
• Time, Rise: 2.96 μs
• Voltage, Gain: 8 V/V
• Voltage, Input: 2 V
• Voltage, Input Offset: 0.3 mV
• Voltage, Noise: 31.5 mV
• Voltage, Supply: 5.5 V
• No. Of Channels: 1
• Isolation Voltage: 3.75kV
• Optocoupler Output Type: Analog
• Input Current: 16mA
• Output Voltage: 3.8V
• Opto Case Style: DIP
• No. Of Pins: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Slew Rate: -
• Gain Bandwidth Product: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 516-1481-5

IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884 Teil 2): 2003-01.
Regulatory Information
The HCPL-7800(A) has been approved by the following organizations:
IEC/EN/DIN EN 60747-5-2 Insulation Characteristics
Notes:
1. Insulation characteristics are guaranteed only within the safety maximum ratings which
must be ensured by protective circuits within the application. Surface Mount Classification is
Class A in accordance with CECC00802.
2. Refer to the optocoupler section of the Isolation and Control Components Designer’s Cata-
log, under Product Safety Regulations section, (IEC/EN/DIN EN 60747-5-2) for a detailed descrip-
tion of Method a and Method b partial discharge test profiles.
3. Refer to the following figure for dependence of PS and IS on ambient temperature.

Description
Installation classification per DIN VDE 0110/1.89, Table 1
Climatic Classification
Pollution Degree (DIN VDE 0110/1.89)
Maximum Working Insulation Voltage
Input to Output Test Voltage, Method b
Input to Output Test Voltage, Method a
Highest Allowable Overvoltage
Safety-limiting values—maximum values
allowed in the event of a failure.
Insulation Resistance at T
(Transient Overvoltage t
for rated mains voltage 300 Vrms
for rated mains voltage 600 Vrms
V
t
V
t
Case Temperature
Input Current
Output Power
m
m
IORM
IORM
= 1 sec, Partial discharge < 5 pC
= 60 sec, Partial discharge < 5 pC
x 1.875 = V
x 1.5 = V
[3]
[3]
PR,
PR,
Type and Sample Test,
100% Production Test with
ini
S
, V
= 10 sec)
IO
= 500 V
[2]
[2]
[1]
UL
Approved under UL 1577, component
recognition program up to V
CSA
Approved under CSA Component Acceptance
Notice #5, File CA 88324.
Symbol
V
V
V
V
T
I
P
R
S,INPUT
S
IORM
PR
PR
IOTM
S,OUTPUT
S
Characteristic
I-IV
I-III
55/100/21
2
891
1670
1336
6000
175
400
600
>10
800
700
600
500
400
300
200
100
0
9
0
ISO
25
T
= 3750 Vrms.
A
50
- CASE TEMPERATURE -
75
100
Unit
V
V
V
V
°C
mA
mW
Ω
PEAK
PEAK
PEAK
PEAK
P S (mW)
I S (mA)
125
150
o
C
175
200