MCP6V06-E/SN Microchip Technology, MCP6V06-E/SN Datasheet - Page 27

• Manufacturer Part Number: MCP6V06-E/SN
• Description: IC OPAMP AUTO-ZERO SNGL 8SOIC
• Manufacturer: Microchip Technology

Specifications of MCP6V06-E/SN

• Slew Rate: 0.5 V/µs
• Amplifier Type: Chopper (Zero-Drift)
• Number Of Circuits: 1
• Output Type: Rail-to-Rail
• Gain Bandwidth Product: 1.3MHz
• Current - Input Bias: 6pA
• Voltage - Input Offset: 3µV
• Current - Supply: 300µA
• Current - Output / Channel: 22mA
• Voltage - Supply, Single/dual (±): 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Op Amp Type: Unity Gain Stable
• No. Of Amplifiers: 1
• Bandwidth: 1.3MHz
• Supply Voltage Range: 1.8V To 5.5V
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Number Of Channels: 1
• Voltage Gain Db: 158 dB
• Common Mode Rejection Ratio (min): 120 dB
• Input Offset Voltage: 0.003 mV
• Operating Supply Voltage: 3 V, 5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -
• Lead Free Status / Rohs Status: Details

4.4.2
The ratiometric circuit in
wire RTD. It corrects for the sensor’s wiring resistance
by subtracting the voltage across the middle R
top R1 does not change the output voltage; it balances
the op amp inputs. Failure (open) of the RTD is
detected by an out-of-range voltage.
FIGURE 4-15:
The voltages at the input of the ADC can be calculated
with the following:
4.4.3
Figure 4-16
and temperature sensor used in a thermocouple
application. The type K thermocouple senses the
temperature at the hot junction (T
voltage at V
© 2008 Microchip Technology Inc.
Where:
R
R
R
V
V
R
100Ω
W
W
W
V
V
CM
DM
V
G
RTD
W
V
V
B
T
RTD
G
DM
CM
W
1
RTD SENSOR
THERMOCOUPLE SENSOR
shows a simplified diagram of an amplifier
proportional to T
=
=
=
=
=
=
=
=
=
10 nF
10 nF
1
G
G
V
------------------------------------------------------------------------------
V
T
+
RTD
RTD
DD
+
2 R
Voltage at the top of R
Voltage at the bottom of R
Voltage across top and middle
R
ADC’s common mode input
ADC’s differential mode input
R
20 kΩ
R
20 kΩ
V
⋅
(
W
–
T
B
V
RTD Sensor.
B
’s
1 µF
R
2.49 kΩ
2.49 kΩ
T
3
+
Figure 4-15
3
2.49 kΩ
2.49 kΩ
–
⁄
(
R
R
R
⁄
V
G
R
2
1
1
B
1
RTD
HJ
)
2
+
(in °C). The amplifier’s
G
+
HJ
W
R
2.55 kΩ
R
2.55 kΩ
1 G
100 kΩ
100 kΩ
100 nF
100 nF
), and produces a
conditions a three
V
2
2
–
R
R
W
3
3
½ MCP6V07
½ MCP6V07
W
)V
RTD
W
RTD
3 kΩ
3 kΩ
ADC
W
V
. The
DD
gain is is set so that V
the output of a temperature sensor, which produces a
voltage proportional to the temperature (in °C) at the
cold junction (T
that V
EQUATION 4-5:
FIGURE 4-16:
Simplified Circuit.
Figure 4-17
this circuit. The dashed red arrow indicates a thermally
conductive connection between the thermocouple and
the MCP9700A; it needs to be very short and have low
thermal resistance.
FIGURE 4-17:
The MCP9700A senses the temperature at its physical
location. It needs to be at the same temperature as the
cold junction (T
V
V
V
V
≈ (10 mV/°C) (T
(hot junction
MCP9700A
1
2
3
4
at T
(cold junction
MCP1541
Type K
≈ T
= (1.00V)
= T
= 250V
4
40 µV/°C
Type K
Thermocouple
V
V
is 0.50V when T
HJ
HJ
CJ
DD
DD
)
at T
(40 µV/°C)
(10 mV/°C) + (0.50V)
shows a more complete implementation of
1
V
+ (V
CJ
1
CJ
CJ
)
), and with a 0.50V offset. V
), and produces V
2
HJ
4.100R
R/250
R/250
– V
MCP6V06/7/8
4
R
– T
V
V
V
/T
Thermocouple Sensor;
Thermocouple Sensor.
3
1
2
3
HJ
)
HJ
CJ
– T
) + (0.50V)
is 10 mV/°C. V
R/250
R/250
0.5696R
CJ
R
R
C
C
R
is 0°C.
MCP6V06
3
DS22093A-page 27
(Figure
C
C
R
R
3 kΩ
3
MCP6V06
represents
2
4-14).
is set so
V
V
4
4