LT1223CS8 Linear Technology, LT1223CS8 Datasheet - Page 9

IC CURRNT FEEDBK AMP100MHZ 8SOIC

LT1223CS8

Manufacturer Part Number
LT1223CS8
Description
IC CURRNT FEEDBK AMP100MHZ 8SOIC
Manufacturer
Linear Technology
Datasheet

Specifications of LT1223CS8

Amplifier Type
Current Feedback
Number Of Circuits
1
Slew Rate
1300 V/µs
-3db Bandwidth
100MHz
Current - Input Bias
1µA
Voltage - Input Offset
1000µV
Current - Supply
6mA
Current - Output / Channel
60mA
Voltage - Supply, Single/dual (±)
8 V ~ 36 V, ±4 V ~ 18 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Output Type
-
Gain Bandwidth Product
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LT1223CS8
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT1223CS8
Quantity:
4 000
Part Number:
LT1223CS8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1223CS8#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
Shutdown
Pin 8 activates a shutdown control function. Pulling more
than 200mA from Pin 8 drops the supply current to less
than 3mA, and puts the output into a high impedance state.
The easy way to force shutdown is to ground Pin 8, using
an open collector (drain) logic stage. An internal resistor
limits current, allowing direct interfacing with no addi-
tional parts. When Pin 8 is open, the LT1223 operates
normally.
Slew Rate
The slew rate of a current feedback amplifier is not inde-
pendent of the amplifier gain configuration the way it is in
a traditional op amp. This is because the input stage and
the output stage both have slew rate limitations. Inverting
amplifiers do not slew the input and are therefore limited
only by the output stage. High gain, noninverting amplifi-
ers are similar. The input stage slew rate of the LT1223 is
about 350V/µs before it becomes nonlinear and is en-
hanced by the normally reverse-biased emitters on the
input transistors. The output slew rate depends on the size
of the feedback resistors. The peak output slew rate is
about 2000V/µs with a 1k feedback resistor and drops
proportionally for larger values. At an output slew rate of
1000V/µs or more, the transistors in the “mirror circuits”
will begin to saturate due to the large feedback currents.
This causes the output to have slew induced overshoot and
is somewhat unusual looking; it is in no way harmful or
dangerous to the device. The photos show the LT1223 in
a noninverting gain of three (R
20V peak-to-peak output slewing at 500V/µs, 1000V/µs
and 2000V/µs.
Settling Time
The Inverting Amplifier Settling Time versus Output Step
curve shows that the LT1223 will settle to within 1mV of
final value in less than 100ns for all output changes of 10V
or less. When operated as an inverting amplifier there is
less than 500µV of thermal settling in the amplifier.
However, when operating the LT1223 as a noninverting
amplifier, there is an additional thermal settling compo-
nent that is about 200µV for every volt of input common
mode change. So a noninverting gain of one amplifier will
U
U
F
= 1k, R
W
G
= 500Ω) with a
U
Output Slew Rate at 2000V/µs Shows Aberrations (See Text)
Output Slew Rate of 1000V/µs
Output Slew Rate of 500V/µs
LT1223
1223 A03
1223 A01
1223 A02
1223fb
9

Related parts for LT1223CS8