EL5106IWZ-T7 Intersil, EL5106IWZ-T7 Datasheet - Page 9

• Manufacturer Part Number: EL5106IWZ-T7
• Description: IC AMP FGA SGL 300MHZ SOT23-6
• Manufacturer: Intersil

Specifications of EL5106IWZ-T7

• Amplifier Type: General Purpose
• Number Of Circuits: 1
• Slew Rate: 4500 V/µs
• -3db Bandwidth: 380MHz
• Current - Input Bias: 1.5µA
• Voltage - Input Offset: 1000µV
• Current - Supply: 1.5mA
• Current - Output / Channel: 100mA
• Voltage - Supply, Single/dual (±): 5 V ~ 12 V, ±2.5 V ~ 6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Gain Bandwidth Product: -

Current Limiting
The EL5106 and EL5306 have no internal current-limiting
circuitry. If the output is shorted, it is possible to exceed the
Absolute Maximum Rating for output current or power
dissipation, potentially resulting in the destruction of the
device.
Power Dissipation
With the high output drive capability of the EL5106 and
EL5306, it is possible to exceed the +125°C Absolute
Maximum junction temperature under certain very high load
current conditions. Generally speaking when R
about 25Ω, it is important to calculate the maximum junction
temperature (T
power supply voltages, load conditions, or package type
need to be modified for the EL5106 and EL5306 to remain in
the safe operating area. These parameters are calculated as
shown in Equation 1:
Revision History
T
JMAX
=
6/4/09
DATE
T
MAX
JMAX
+
(
θ
JA
) for the application to determine if
×
n
×
PD
REVISION
MAX
FN7357.6
9
)
L
Removed obsolete, leaded devices EL5106IW-T7, EL5106IW-T7A; EL5106IS-T7, EL5106IS-
T13; EL5306IS, EL5306IS-T7, EL5306IS-T13; EL5306IU, EL5306IU-T7, EL5306IU-T13
Corrected Figure references in “Gain Setting” on page 7 (Fig 14 callout was referencing Fig
13; Fig 15 callout was referencing Fig 14; Fig 16 callout was referencing Fig 15) .
Updated pin descriptions to match pin names of EL5306.
Applied Intersil Standards: Updated Pb-free bullet in Features, Updated ordering information
by removing tape and reel column and adding standard reference note and updating note to
match lead finish, updated caution statement to legal's suggested verbiage. Changed date
and Rev'd to 6.
Updated POD MDP0038 toP6.064A - P6.064A replaces 6 Ld SOT-23
(same dimensions, just MDP0038 had both 5 & 6 Ld SOT23s w/dimensions listed in table)
Updated POD MDP0027 to M8.15E - M8.15E replaces MDP0027 8 Ld SOIC (same
dimensions, just MDP0027 had 8, 14, 16, 20, 24, 28 Ld SOICS with dimensions listed in table)
P1, added Note 2 "The part marking is located on the bottom of the part" for SOT-23 package
falls below
EL5106, EL5306
(EQ. 1)
where:
PD
Equation 2:
where:
PD
T
θ
n = Number of amplifiers in the package
PD
the package
V
I
V
R
SMAX
MAX
MAX
JA
MAX
S
OUTMAX
L
MAX
= Load resistance
= Supply voltage
= Thermal resistance of the package
for each amplifier can be calculated as shown in
=
= Maximum ambient temperature
= Maximum bias supply current
= Maximum power dissipation of each amplifier in
2 (
×
= Maximum output voltage (required)
CHANGE
V
S
×
I
SMAX
)
+
(
V
S
- V
OUTMAX
)
×
September 21, 2010
V
--------------------------- -
OUTMAX
R
L
FN7357.6
(EQ. 2)