EL5132ISZ-T7 Intersil, EL5132ISZ-T7 Datasheet - Page 10
![IC VFA 670MHZ ULT LO VOLT 8SOIC](/photos/12/58/125823/el5132isz-t7_sml.jpg)
EL5132ISZ-T7
Manufacturer Part Number
EL5132ISZ-T7
Description
IC VFA 670MHZ ULT LO VOLT 8SOIC
Manufacturer
Intersil
Datasheet
1.EL5132IS.pdf
(13 pages)
Specifications of EL5132ISZ-T7
Amplifier Type
Voltage Feedback
Number Of Circuits
1
Slew Rate
1000 V/µs
Gain Bandwidth Product
3GHz
-3db Bandwidth
670MHz
Current - Input Bias
12µA
Voltage - Input Offset
500µV
Current - Supply
11mA
Current - Output / Channel
140mA
Voltage - Supply, Single/dual (±)
5 V ~ 12 V, ±2.5 V ~ 6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Output Type
-
Other names
EL5132ISZ-T7TR
Typical Performance Curves
Applications Information
Product Description
The EL5132, EL5133 is a voltage feedback operational
amplifier designed for communication and imaging
applications requiring very low voltage and current noise. It
also features low distortion while drawing moderately low
supply current and is built on Intersil's proprietary high-speed
complementary bipolar process. The EL5132, EL5133 uses
a classical voltage-feedback topology which allows them to
be used in a variety of applications where current-feedback
amplifiers are not appropriate because of restrictions placed
upon the feedback element used with the amplifier.
Gain-Bandwidth Product and the -3dB Bandwidth
The EL5132, EL5133 has a gain-bandwidth product of
3000MHz while using only 11mA of supply current. For gains
greater than 10, their closed-loop -3dB bandwidth is
approximately equal to the gain-bandwidth product divided
by the noise gain of the circuit. For gains of 10, higher-order
poles in the amplifiers' transfer function contribute to even
higher closed loop bandwidths. For example, the EL5132,
EL5133 have a -3dB bandwidth of 670MHz at a gain of 10,
dropping to 150MHz at a gain of 30. It is important to note
that the EL5132, EL5133 is designed so that this “extra”
bandwidth in low-gain application does not come at the
expense of stability. As seen in the typical performance
curves, the EL5132, EL5133 in a gain of only 10 exhibited
0.5dB of peaking with a 500Ω load.
10
-0.05
-0.15
-0.20
-0.05
-0.15
-0.20
0.20
0.15
0.05
0.2
0.1
0.0
0
0
0
0
(Continued)
10
10
FIGURE 36. DIFFERENTIAL PHASE (°)
FIGURE 35. DIFFERENTIAL GAIN (%)
20
20
EL5132, EL5133
30
30
40
40
50
50
Output Drive Capability
The EL5132 and EL5133 are is designed to drive a low
impedance load. It can easily drive 6V
load. This high output drive capability makes the EL5132,
EL5133 an ideal choice for RF, IF, and video applications.
Furthermore, the EL5132, EL5133 is current-limited at the
output, allowing it to withstand momentary short to ground.
However, the power dissipation with output-shorted cannot
exceed the power dissipation capability of the package.
Driving Cables and Capacitive Loads
Although the EL5132, EL5133 is designed to drive low
impedance load, capacitive loads will decreases the
amplifier's phase margin. As shown in the performance
curves, capacitive load can result in peaking, overshoot and
possible oscillation. For optimum AC performance,
capacitive loads should be reduced as much as possible or
isolated with a series resistor between 5Ω to 20Ω. When
driving coaxial cables, double termination is always
recommended for reflection-free performance. When
properly terminated, the capacitance of the coaxial cable will
not add to the capacitive load seen by the amplifier.
Disable/Power-Down
The EL5132 amplifier can be disabled placing its output in a
high impedance state. When disable, the amplifier current is
reduced to 12µA. The EL5132 is disabled when it CE pin is
pulled up to within 1V of the power supply. Similarly, the
amplifier is enabled by floating or pulling its CE pin to at least
3V below the positive supply. For ±5V supply, this means
that an EL5132 amplifier will be enabled when CE is 2V or
60
60
70
70
80
80
90
90
100
100
P-P
signal into a 500Ω
May 4, 2007
FN7382.8