71M6532D-IGTR/F Maxim Integrated Products, 71M6532D-IGTR/F Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
71M6532D-IGTR/F
Manufacturer Part Number
71M6532D-IGTR/F
Description
IC ENERGY METER 128KB 100-LQFP
Manufacturer
Maxim Integrated Products
Datasheet
1.71M6531D-IMRF.pdf
(120 pages)
Specifications of 71M6532D-IGTR/F
Mounting Style
SMD/SMT
Package / Case
LQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
71M6532D-IGTR/F
Manufacturer:
Maxim Integrated
Quantity:
10 000
an accumulation interval and CROSS always toggles near the end of each multiplexer frame.
The internal bias voltage, VBIAS (typically 1.6 V), is used by the ADC when measuring the temperature
and battery monitor signals.
reference. It is used to determine the die temperature. The MPU may request an alternate multiplexer
cycle containing the temperature sensor output by asserting MUX_ALT.
The primary use of the temperature data is to determine the magnitude of compensation required to offset
the thermal drift in the system (see Section
the battery and a scaled fraction of the battery voltage is applied to the ADC input. After each alternative
MUX frame, the result of the ADC conversion is available at XRAM address 0x0B. BME is ignored and
assumed zero when system power is not available (V1 < VBIAS). See Section
VB) are sampled, and the ADC counts obtained are stored in XRAM where they can be accessed by the
CE and, if necessary, by the MPU. Alternate multiplexer cycles are initiated less frequently by the MPU to
gather access to the slow temperature and battery signals.
Figure
(for the 71M6531D/F, the current input for phase A is a single pin [IA]).
Data Sheet 71M6531D/F-71M6532D/F
the number of multiplexer frames in an accumulation interval is always even. Operation with
CHOP_E[1:0] = 00 does not require control of the chopping mechanism by the MPU while eliminating the
offset for temperature measurement.
In the second toggle state, CHOP_E[1:0] = 11, no ALT frame is forced during the last multiplexer cycle in
1.2.6
The 71M6531D/F and 71M6532D/F include an on-chip temperature sensor implemented as a bandgap
1.2.7
The battery voltage is measured by the ADC during alternative multiplexer frames if the BME (Battery
Measure Enable) bit in the I/O RAM is set. While BME is set, an on-chip 45 kΩ load resistor is applied to
1.2.8
The AFE functions as a data acquisition system, controlled by the MPU. The main signals (IA, VA, IB and
14
5 shows the block diagram of the AFE, with current inputs shown only as differential pair of pins
Temperature Sensor
Battery Monitor
AFE Functional Description
Figure 5: AFE Block Diagram (Shown for the 71M6532D/F)
IAP
IAN
© 2005-2010 TERIDIAN Semiconductor Corporation
IBP
IBN
VA
VB
VBAT
SENSOR
TEMP
EQU
MUX_ALT
MUX_DIV
MUX
3.4 Temperature
VREF_CAL
VREF_DIS
VBIAS
VREF
VADC
VREF
Compensation).
CONVERTER
VREF
VBIAS
ADC_E
∆Σ ADC
FIR_LEN
FIR
22
5.4.4 Battery
FDS 6531/6532 005
Monitor.
v1.3