STEVAL-IHM025V1 STMicroelectronics, STEVAL-IHM025V1 Datasheet
STEVAL-IHM025V1
Specifications of STEVAL-IHM025V1
Available stocks
Related parts for STEVAL-IHM025V1
STEVAL-IHM025V1 Summary of contents
Page 1
... Combining ST proprietary control ICs with the most advanced short-circuit-rugged IGBT system technology, this device is ideal for 3- /min phase inverters in applications such as home appliances and air conditioners. SLLIMM™ trademark of STMicroelectronics. Marking GIPL14K60 SDIP-38L Doc ID 15589 Rev 5 STGIPL14K60 SLLIMM™ ...
Page 2
Contents Contents 1 Internal block diagram and pin configuration . . . . . . . . . . . . . . . . . . . . 3 2 Electrical ratings . . . . . . . ...
Page 3
STGIPL14K60 1 Internal block diagram and pin configuration Figure 1. Internal block diagram Internal block diagram and pin configuration Doc ID 15589 Rev 5 3/22 ...
Page 4
Internal block diagram and pin configuration Table 2. Pin description Pin ...
Page 5
STGIPL14K60 Table 2. Pin description (continued) Pin Figure 2. Pin layout (bottom view) Internal block diagram and pin configuration Symbol P Positive DC input N Negative DC input for U phase phase output ...
Page 6
Electrical ratings 2 Electrical ratings 2.1 Absolute maximum ratings Table 3. Inverter part Symbol V Supply voltage applied between P-N PN Supply voltage (surge) applied between P-N V PN(surge Each IGBT collector emitter voltage (V CES Each ...
Page 7
STGIPL14K60 Table 5. Total system Symbol Isolation withstand voltage applied between each V ISO pin and heatsink plate (AC voltage 60sec.) (1) T Operating junction temperature j T Module case operation temperature C 1. The maximum junction temperature ...
Page 8
Electrical characteristics 3 Electrical characteristics °C unless otherwise specified. j Table 7. Inverter part Symbol Parameter Collector-emitter V CE(sat) saturation voltage Collector-cut off current I CES ( “logic state” Diode forward voltage F ...
Page 9
STGIPL14K60 Figure 3. Switching time test circuit Figure 4. Switching time definition IN(ON) Figure 4 "Switching time definition" refers to HIN inputs (active high). For LIN inputs (active low), V must be inverted for turn-on ...
Page 10
Electrical characteristics 3.1 Control part Table 8. Low voltage power supply (V Symbol Parameter hysteresis cc_hys turn ON threshold cc_thON turn OFF threshold cc_thOFF cc Undervoltage quiescent I qccu ...
Page 11
STGIPL14K60 Table 11. OPAMP characteristics (V Symbol Parameter V Input offset voltage io I Input offset current io (1) I Input bias current ib Input common mode voltage V icm range V Low level output voltage OL V High level ...
Page 12
Electrical characteristics Table 13. Truth table Condition SD/OD Shutdown enable half-bridge 3-state Interlocking half-bridge 3-state 0 ‘’logic state” half-bridge 3-state 1 “logic state” low side direct driving 1 “logic state” high side direct driving Note: X: don’t care. Figure 5. ...
Page 13
STGIPL14K60 3.1.1 NTC thermistor Table 14. NTC thermistor Symbol Resistance R 25 Resistance R 125 B B-constant T Operating temperature Equation 1: resistance variation vs. temperature Where T are temperatures in Kelvins Figure 7. NTC resistance vs. temperature Parameter Test ...
Page 14
Electrical characteristics 3.2 Waveforms definitions Figure 8. Dead time and interlocking waveforms definitions CONTROL SIGNAL EDGES OVERLAPPED: INTERLOCKING + DEAD TIME CONTROL SIGNALS EDGES SYNCHRONOUS (*): DEAD TIME CONTROL SIGNALS EDGES NOT OVERLAPPED, BUT INSIDE THE DEAD TIME: DEAD TIME ...
Page 15
STGIPL14K60 4 Smart shutdown function The STGIPL14K60 integrates a comparator for fault sensing purposes. The comparator non-inverting input (CIN) can be connected to an external shunt resistor in order to implement a simple over-current protection function. When the comparator triggers, ...
Page 16
Applications information 5 Applications information Figure 10. Typical application circuit 16/22 Doc ID 15589 Rev 5 STGIPL14K60 ...
Page 17
STGIPL14K60 5.1 Recommendations ● Input signal HIN is active high logic. A 85kΩ (typ.) pull down resistor is built-in for each high side input external RC filter is used, for noise immunity, pay attention to the variation of ...
Page 18
Package mechanical data 6 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available ...
Page 19
STGIPL14K60 Figure 11. SDIP-38L drawing dimensions Doc ID 15589 Rev 5 Package mechanical data 8142868_F 19/22 ...
Page 20
Package mechanical data Figure 12. SDIP-38L tube dimensions 20/22 Doc ID 15589 Rev 5 STGIPL14K60 8304140_A ...
Page 21
STGIPL14K60 7 Revision history Table 17. Document revision history Date 16-Apr-2009 29-Mar-2010 14-Jun-2010 21-Sep-2010 09-Mar-2011 Revision 1 Initial release Inserted Figure 5, Figure 6 Updated Section 3.1: Control part 2 Section 6. Minor text changes to improve readability. Document status ...
Page 22
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...