STEVAL-IFS013V2 STMicroelectronics, STEVAL-IFS013V2 Datasheet
STEVAL-IFS013V2
Specifications of STEVAL-IFS013V2
Related parts for STEVAL-IFS013V2
STEVAL-IFS013V2 Summary of contents
Page 1
... ZigBee® USB dongle demonstration kit (STEVAL-IFS013V2) 1 Introduction This document describes the hardware and software of the STMicroelectronics™ ZigBee USB dongle demonstration kit working under the Microsoft operating systems. The purpose of this design is to demonstrate the key features of STMicroelectronics ZigBee PRO compliant wireless networking solutions. ZigBee PRO, the leading wireless control and ...
Page 2
Contents Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
UM0602 List of tables Table 1. Serial commands supported on sensor and sink . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of figures List of figures Figure 1. Device manager window ...
Page 5
... UM0602 2 Description The ZigBee USB dongle demonstration kit tool is designed to demonstrate several STMicroelectronics products: ■ SPZB260-PRO is a low power consumption ZigBee module optimized for embedded applications. It enables OEMs to easily add wireless capability to electronic devices. The module is based on SN260 ZigBee network processor which integrates 2.4 GHz, IEEE 802 ...
Page 6
Getting started 3 Getting started 3.1 System requirements In order to use the USB to ZigBee dongle evaluation kit with the Windows operating system, a recent version of Windows, such as Windows XP, Windows 98, Windows Millennium or Windows 2000 ...
Page 7
UM0602 Figure 1. Device manager window 3.4 Hardware installation Figure 2 shows the location of the main components of the evaluation board. The schematic drawing is given in Figure 2. USB to ZigBee dongle based on STM32 and SPZB260-PRO Figure ...
Page 8
Getting started 3.4.1 Power supply The USB to ZigBee dongle evaluation board is directly supplied by the USB connector (bus- powered) and therefore does not require an external voltage supply. 3.4.2 STM32 JTAG interface The 8-pin connector CN3 must be ...
Page 9
... Flash, data Flash/EEPROM or any other memory connected to the microcontroller even a serial Flash (through SPI or I dongle evaluation kit is DFU used to program the internal Flash memory. Refer to the UM0412, DfuSe USB device firmware upgrade STMicroelectronics extension, for more details on the driver installation and PC user interface. 4.2 Virtual COM port In modern PCs, USB is the standard communication port for almost all peripherals ...
Page 10
... ZigBee coordinator device, and it forms the network automatically on first startup and retains these settings across reboots. Once the sink application starts running, led LD2 on your evaluation STEVAL-IFS013V2 board will blink (visual signal that the node is active). ...
Page 11
UM0602 4.3.4 Notes and limitations ● This application defaults to using a fixed set of network parameters, with a default channel setting of 26. (Remove the #define USE_HARDCODED_NETWORK_SETTINGS line in the common.h header file to allow the application to dynamically ...
Page 12
Running the USB to ZigBee dongle evaluation kit 5 Running the USB to ZigBee dongle evaluation kit First, connect the evaluation board to the PC via the USB cable result, the evaluation board is enumerated as a STM™ ...
Page 13
UM0602 Figure 4. Windows HyperTerminal serial port settings Running the USB to ZigBee dongle evaluation kit Doc ID 15114 Rev 2 13/18 ...
Page 14
... Once is the device in the DFU mode, you can simply update main application with support of tools coming from STM in DfuSe package. For further information, please refer to user manual UM0412 - Getting started with DfuSe USB device firmware upgrade STMicroelectronics extension, available online from www.st.com/mcu. 14/18 Doc ID 15114 Rev 2 ...
Page 15
UM0602 7 Appendix Figure 5. Evaluation board schematics - microcontroller part Doc ID 15114 Rev 2 Appendix 15/18 ...
Page 16
Appendix Figure 6. Evaluation board schematics - ZigBee and interface connectors part 16/18 Doc ID 15114 Rev 2 UM0602 ...
Page 17
... Revision history Table 3. Document revision history Date 13-Nov-2008 26-Aug-2009 Revision 1 Initial release. Document reformatted, replaced devices: STEVAL-IFS013V1 by STEVAL-IFS013V2, STM32F103C6T6 by STM32F103CBT6 and SPZB260 by SPZB260-PRO, SN260 debug interface by SPZB260- 2 PRO debug interface, removed STEVAL-IFS009V1, updated Section 3.2.2, Section Figure 6 and Table 1, added Doc ID 15114 Rev 2 ...
Page 18
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...