DR-TRC102-915-DK RFM, DR-TRC102-915-DK Datasheet
DR-TRC102-915-DK
Specifications of DR-TRC102-915-DK
Related parts for DR-TRC102-915-DK
DR-TRC102-915-DK Summary of contents
Page 1
... DR-TRC102-433-DK (430-439 MHz) • DR-TRC102-868-DK (860-879 MHz) • DR-TRC102-915-DK (900-929 MHz) The TRC102 Development kits allows for complete evaluation and application development of RFM’s SRR (Short Range Radio) line of RFIC’s. A communication link or Range Test can be executed with the Data Terminal to evaluate system performance ...
Page 2
... FIFO overflow/TX register underrun · Wake-up timer timeout · Negative pulse on the interrupt input pin nINT · Supply voltage below the preprogrammed value is detected Rev00 RF Monolithics, Inc. (800) 704-6079 toll-free in U.S. and Canada 2-way Comm. header Figure 1. TRC102 Development Board www.rfm.com Email: support@rfm.com 2 ...
Page 3
... Development Board Operation Antennas Two monopole antennas are included that are matched for performance to the ground plane area of the DR boards. The antennas are a critical part of the performance of the communication link, thus, a monopole antenna requires a good ground plane for proper performance. Power Supply Two pins are provided for connection of an external power supply or a portable battery pack ...
Page 4
... Jumper and apply an ammeter between the two pins. 2-way Comm Header (J3) Installation of J3 allows the DR board to power-up in comm link mode. J3 must be installed first before power applied to the board in order for the board to initialize in comm link mode. After power-up, follow the Quick Start Guide configuration for comm ...
Page 5
... The packet structure for the comm link and range test is given below. The packet demonstrates the use of PREAMBLE 0xAA PREAMBLE 0xAA Rev00 RF Monolithics, Inc. (800) 704-6079 toll-free in U.S. and Canada SYNCH BYTE 0x2D SYNCH BYTE 0XD4 DATA [N] CHKSUM CHKSUM DATA [N+1] ........... www.rfm.com Email: support@rfm.com 5 ...
Page 6
... Configure both boards as follows: Range Test A range test can be performed by configuring both DR boards for a comm link as above and clicking on the “Enable Range Test” button at the top of the Data Terminal Window. When the range test is activated it will send a default message of “<TX> Range Test Data” and the enable button will flash red. At this point the serial cable may be disconnected for free movement around the area of interest ...
Page 7
... A custom range test message bytes may be sent by simply typing in the message desired and pressing the “Enable Range Test” button. Rev00 RF Monolithics, Inc. (800) 704-6079 toll-free in U.S. and Canada www.rfm.com Email: support@rfm.com 7 ...
Page 8
... Battery Packs The kit includes four “AAA” batteries and two battery packs that hold 2 “AAA” batteries each. One pack may be connected and used to free-roam an area for range test. Rev00 RF Monolithics, Inc. (800) 704-6079 toll-free in U.S. and Canada www.rfm.com Email: support@rfm.com 8 ...
Page 9
... Rev00 RF Monolithics, Inc. (800) 704-6079 toll-free in U.S. and Canada www.rfm.com Email: support@rfm.com 9 ...
Page 10
... CRYSTAL,10 MHZ C8051F330 SILICON LABS MICROCONTROLLER,20-QFN DB-9 CONNECTOR HDR,2-PIN CONN,HEADER,DUAL ROW,5 PIN CONN,SMA,STRAIGHT VERTICAL,PCB JACK IC,XCVR W/AUTO SHUTDOWN,RS-232,120 kbps,16 TSSOP TRC102 RFIC, TSSOP-16 Rev00 RF Monolithics, Inc. (800) 704-6079 toll-free in U.S. and Canada Bill of Material for DR-TRC102-433 QTY REF 10 S1,D5-D8,L4,R1-R4 1 L3* 1 L2* 1 L1* ...
Page 11
... Bill of Material for DR-TRC102-868/915 ITEM DESCRIPTION COMPONENT NOT USED IN ASSY IND,0603,22 nH,10%, COILCRAFT IND,CHIP,0603CS,100 nH,5%,COILCRAFT IND,0603,8.7 nH,+/- 10%, COILCRAFT RES,CHIP,0603,1.0K OHM,+/-5%, TIN TERMINATIONS RES,CHIP,0603,10K OHM,+/-5%, TIN TERMINATIONS RES,CHIP,0603,470 OHM,+/-5%, TIN TERMINATIONS CAP,CHIP,0603,COG,1.2 pF,50V,SOLDER MNT CAP,CHIP,0603,COG,2.7 pF,50V,SOLDER MNT CAP,CHIP,0603,COG,10 pF,50V,SOLDER MNT CAP,CHIP,0603,COG,100 pF,50V,SOLDER MNT CAP,CHIP,0603,X7R,1000 pF,50V,SOLDER MNT CAP,CHIP,0603,X7R, ...