HSP50214BVCZ Intersil, HSP50214BVCZ Datasheet - Page 48
![IC DOWNCONVERTER 14BIT 120-MQFP](/photos/14/15/141537/120-mqfp_sml.jpg)
HSP50214BVCZ
Manufacturer Part Number
HSP50214BVCZ
Description
IC DOWNCONVERTER 14BIT 120-MQFP
Manufacturer
Intersil
Datasheet
1.HSP50214BVCZ.pdf
(62 pages)
Specifications of HSP50214BVCZ
Function
Downconverter
Rf Type
AMPS, CDMA, GSM, TDMA
Package / Case
120-MQFP, 120-PQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HSP50214BVCZ
Manufacturer:
AD
Quantity:
1 001
NOTE: In the HSP50214B, if the SYNCIN1 occurs when the NCO is not updating, the load signal is held internal to the part until the next NCO
update.
POSITION
POSITION
POSITION
POSITION
POSITION
POSITION
29-14
31-10
13-0
31-0
BIT
BIT
N/A
BIT
BIT
BIT
N/A
BIT
N/A
9-0
31
30
Reserved
Integration Mode
Integration Interval
Input Threshold
Start Input Level
Detector AGC
Integrator
Carrier Center
Frequency
Reserved
Carrier Phase Offset
Carrier Frequency
Strobe
Carrier Phase Strobe
CONTROL WORD 2: INPUT LEVEL DETECTOR START STROBE (SYNCHRONIZED TO CLKIN)
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
FUNCTION
CONTROL WORD 3: CARRIER NCO CENTER FREQUENCY (SYNCHRONIZED TO CLKIN)
CONTROL WORD 5: CARRIER FREQUENCY STROBE (SYNCHRONIZED TO CLKIN)
CONTROL WORD 6: CARRIER PHASE STROBE (SYNCHRONIZED TO CLKIN)
CONTROL WORD 4: CARRIER PHASE OFFSET (SYNCHRONIZED TO CLKIN)
CONTROL WORD 1: INPUT LEVEL DETECTOR (SYNCHRONOUS TO CLKIN)
48
Reserved.
0- Integration of magnitude error stops when the interval counter times out.
1- Integration runs continuously. When the interval counter times out, the integrator reloads, and the
results of the integration is sent to a register for the processor to read.
These are the top 16-bits of the 18-bit integration counter, ICPrel. ICPrel = (N)/4+1; where N is the
desired integration period in CLKIN cycles, defined as the number of input samples to be integrated. N
must be a multiple of 4: [0, 4, 8, 12, 16.... , 2
zeros must be accounted for, as they will be added to the threshold! If the gated input mode is used, the
same input sample will be accumulated multiple times.
Input Magnitude Threshold. Bits 12-0 correspond to input bits 12-0. The magnitude of the input is added
to this threshold, where the threshold is a signed number. Bit 13 is the MSB.
Writing to this location starts/restarts the input AGC error integrator. The integrator will either restart or
stop when the integration interval counter times out depending on bit 30 of Control Register 1 (see
Microprocessor Write Section).
These bits control the frequency of the Carrier NCO. The frequency range of the NCO is ± f
f
This location is a holding register. After loading, a transfer to the active register is done by writing to
Control Word 5 or by generating a SYNCIN1 with Control Word 0, Bit 20 set to 1. The Carrier NCO only
updates ENI is active.
Reserved.
These bits, PO, are used to offset the phase of the carrier NCO. The bits are computed by the Equation
PO = INT[(2
bit offset binary representation. Bit 9 is the MSB. This location is a holding register. After loading, a
transfer to the active register is done by writing to Control Word 6 or by generating a SYNCIN1 with
Control Word 0, Bit 20 set to 1. The carrier NCO only updates when ENI is active.
Writing to this address updates the carrier frequency Control Word from the Holding Register.
Writing to this address updates the carrier phase offset Control Word with the value written to the phase
offset (PO) register.
S
is the input sample rate. The bits are computed by the equation N = (F
10
φ
off
)/ 2π]
HSP50214B
HEX
; (-π <φ
off
< π) for 10-bit 2’s complement representation or from 0 to 2π for 10-
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
18
]. Bit 29 is the MSB. If the input is interpolated, then the
NCO
/ f
S
)*2
32
. Bit 31 is the MSB.
S
/ 2 where
May 1, 2007
FN4450.4