SI4330-B1-FM Silicon Laboratories Inc, SI4330-B1-FM Datasheet - Page 41

• Manufacturer Part Number: SI4330-B1-FM
• Description: IC RCVR ISM 960MHZ 3.6V 20-QFN
• Manufacturer: Silicon Laboratories Inc
• Type: ISM Receiverr

Specifications of SI4330-B1-FM

• Package / Case: 20-QFN
• Frequency: 960MHz
• Sensitivity: -118dBm
• Data Rate - Maximum: 128kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Current - Receiving: 18.5mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 1.8 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Operating Frequency: 240 MHz to 960 MHz
• Operating Supply Voltage: 3 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Current: 18.5 mA
• Package: 20QFN EP
• Maximum Data Rate: 256 Kbps
• Transmission Media Type: Wireless
• Power Supply Type: Analog
• Typical Operating Supply Voltage: 3 V
• Minimum Operating Supply Voltage: 1.8 V
• Maximum Operating Supply Voltage: 3.6 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Applications: -
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1629-5; SI4330-V2-FM

8.2. Microcontroller Clock
The 30 MHz crystal oscillator frequency is divided down internally and may be output to the microcontroller through
GPIO2. This feature is useful to lower BOM cost by using only one crystal in the system. The system clock
frequency is selectable from one of 8 options, as shown below. Except for the 32.768 kHz option, all other
frequencies are derived by dividing the crystal oscillator frequency. The 32.768 kHz clock signal is derived from an
internal RC oscillator or an external 32 kHz crystal. The default setting for GPIO2 is to output the microcontroller
clock signal with a frequency of 1 MHz.
If the microcontroller clock option is being used there may be the need of a system clock for the microcontroller
while the Si4330 is in SLEEP mode. Since the crystal oscillator is disabled in SLEEP mode in order to save current,
the low-power 32.768 kHz clock can be automatically switched to become the microcontroller clock. This feature is
called enable low frequency clock and is enabled by the enlfc bit in “Register 0Ah. Microcontroller Output Clock."
When enlfc = 1 and the chip is in SLEEP mode then the 32.768 kHz clock will be provided to the microcontroller as
the system clock, regardless of the setting of mclk[2:0]. For example, if mclk[2:0] = 000, 30 MHz will be provided
through the GPIO output pin to the microcontroller as the system clock in all IDLE or RX states. When the chip
enters SLEEP mode, the system clock will automatically switch to 32.768 kHz from the RC oscillator or 32.768
XTAL.
Another available feature for the microcontroller clock is the clock tail, clkt[1:0] in “Register 0Ah. Microcontroller
Output Clock." If the low frequency clock feature is not enabled (enlfc = 0), then the system clock to the
microcontroller is disabled in SLEEP mode. However, it may be useful to provide a few extra cycles for the
microcontroller to complete its operation prior to the shutdown of the system clock signal. Setting the clkt[1:0] field
will provide additional cycles of the system clock before it shuts off.
If an interrupt is triggered, the microcontroller clock will remain enabled regardless of the selected mode. As soon
as the interrupt is read the state machine will then move to the selected mode. The minimum current consumption
will not be achieved until the interrupt is read. For instance, if the chip is commanded to SLEEP mode but an
interrupt has occurred the 30 MHz XTAL will not be disabled until the interrupt has been cleared.
Add R/W
0A
R/W
Microcontroller Output Clock
Function/Description
clkt[1:0]
mclk[2:0]
00
01
10
11
000
001
010
011
100
101
110
111
D7
D6
Rev 1.0
Clock Frequency
clkt[1]
D5
32.768 kHz
128 cycles
256 cycles
Clock Tail
512 cycles
0 cycles
30 MHz
15 MHz
10 MHz
4 MHz
3 MHz
2 MHz
1 MHz
clkt[0]
D4
enlfc
D3
mclk[2] mclk[1] mclk[0]
D2
D1
Si4330-B1
D0
POR Def.
06h
41