SI4330-B1-FM Silicon Laboratories Inc, SI4330-B1-FM Datasheet - Page 50

• Manufacturer Part Number: SI4330-B1-FM
• Description: IC RCVR ISM 960MHZ 3.6V 20-QFN
• Manufacturer: Silicon Laboratories Inc
• Type: ISM Receiverr

Specifications of SI4330-B1-FM

• Package / Case: 20-QFN
• Frequency: 960MHz
• Sensitivity: -118dBm
• Data Rate - Maximum: 128kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Current - Receiving: 18.5mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 1.8 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Operating Frequency: 240 MHz to 960 MHz
• Operating Supply Voltage: 3 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Current: 18.5 mA
• Package: 20QFN EP
• Maximum Data Rate: 256 Kbps
• Transmission Media Type: Wireless
• Power Supply Type: Analog
• Typical Operating Supply Voltage: 3 V
• Minimum Operating Supply Voltage: 1.8 V
• Maximum Operating Supply Voltage: 3.6 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Applications: -
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1629-5; SI4330-V2-FM

Si4330-B1
8.9. Antenna Diversity
To mitigate the problem of frequency-selective fading due to multi-path propagation, some radio systems use a
scheme known as antenna diversity. In this scheme, two antennas are used. Each time the radio enters RX mode
the receive signal strength from each antenna is evaluated. This evaluation process takes place during the
preamble portion of the packet. The antenna with the strongest received signal is then used for the remainder of
that RX packet.
This chip fully supports antenna diversity with an integrated antenna diversity control algorithm. The required
signals needed to control an external SPDT RF switch (such as PIN diode or GaAs switch) are available on the
GPIOx pins. The operation of these GPIO signals is programmable to allow for different antenna diversity
architectures and configurations. The antdiv[2:0] bits are found in register 08h “Operating & Function Control 2.”
The GPIO pins are capable of sourcing up to 5 mA of current, so it may be used directly to forward-bias a PIN
diode if desired.
The antenna diversity algorithm will automatically toggle back and forth between the antennas until the packet
starts to arrive. The recommended preamble length for optimal antenna selection is 8 bytes. A special antenna
diversity algorithm (antdiv[2:0] = 110 or 111) is included that allows for shorter preamble lengths for beacon mode in
TDMA-like systems where the arrival of the packet is synchronous to the receiver enable. The recommended
preamble length to obtain optimal antenna selection for synchronous mode is 4 bytes.
50
Add R/W Function/Description
08
antdiv[2:0]
R/W
000
001
010
011
100
101
110
111
Operating & Function
Antenna Diversity Algorithm
Antenna Diversity Algorithm
Antenna Diversity Algorithm in Beacon Mode
Antenna Diversity Algorithm in Beacon Mode
Control 2
GPIO Ant1
0
1
0
1
Table 16. Antenna Diversity Control
antdiv[2] antdiv[1] antdiv[0] rxmpk Reserved enldm ffclrrx Reserved
RX State
D7
D6
GPIO Ant2
1
0
1
0
Rev 1.0
D5
D4
GPIO Ant1
D3
0
0
1
1
0
1
0
1
D2
Non RX State
D1
GPIO Ant2
D0
0
0
1
1
0
1
0
1
POR Def.
00h