XBP24-ACI-001 Digi International/Maxstream, XBP24-ACI-001 Datasheet - Page 30
![no-image](/images/no-image-200.jpg)
XBP24-ACI-001
Manufacturer Part Number
XBP24-ACI-001
Description
MODULE 802.15.4 100MW CHIP ANT
Manufacturer
Digi International/Maxstream
Series
XBEE-PRO™r
Specifications of XBP24-ACI-001
Frequency
2.4GHz
Data Rate - Maximum
250kbps
Modulation Or Protocol
802.15.4
Applications
Home/Building Automation, Industrial Control, ZigBee™
Power - Output
20dBm (100mW)
Sensitivity
-100dBm
Voltage - Supply
2.8 V ~ 3.4 V
Current - Receiving
55mA
Current - Transmitting
215mA @ 3.3V
Data Interface
PCB, Through Hole
Antenna Connector
On-Board, Chip
Operating Temperature
-40°C ~ 85°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Table 3‐02. XBee®/XBee‐PRO® Commands ‐ Networking & Security (Sub‐categories designated within {brackets})
* Firmware version in which the command was first introduced (firmware versions are numbered in hexadecimal notation.)
XBee®/XBee‐PRO® RF Modules ‐ 802.15.4 ‐ v1.xEx [2009.09.23]
AT
Command
AI ( v1.x80*)
DA ( v1.x80*)
FP ( v1.x80*)
AS ( v1.x80*)
ED ( v1.x80*)
EE ( v1.xA0*)
KY ( v1.xA0*)
Command
Category
Networking
{Association}
Networking
{Association}
Networking
{Association}
Networking
{Association}
Networking
{Association}
Networking
{Security}
Networking
{Security}
Name and Description
Association Indication. Read errors with the last association request:
0x00 - Successful Completion - Coordinator successfully started or End Device
0x01 - Active Scan Timeout
0x02 - Active Scan found no PANs
0x03 - Active Scan found PAN, but the CoordinatorAllowAssociation bit is not set
0x04 - Active Scan found PAN, but Coordinator and End Device are not
0x05 - Active Scan found PAN, but the Coordinator ID parameter does not match
0x06 - Active Scan found PAN, but the Coordinator CH parameter does not match the
0x07 - Energy Scan Timeout
0x08 - Coordinator start request failed
0x09 - Coordinator could not start due to invalid parameter
0x0A - Coordinator Realignment is in progress
0x0B - Association Request not sent
0x0C - Association Request timed out - no reply was received
0x0D - Association Request had an Invalid Parameter
0x0E - Association Request Channel Access Failure. Request was not transmitted -
0x0F - Remote Coordinator did not send an ACK after Association Request was sent
0x10 - Remote Coordinator did not reply to the Association Request, but an ACK was
0x11 - [reserved]
0x12 - Sync-Loss - Lost synchronization with a Beaconing Coordinator
0x13 - Disassociated - No longer associated to Coordinator
0xFF - RF Module is attempting to associate
Force Disassociation. End Device will immediately disassociate from a Coordinator (if
associated) and reattempt to associate.
Force Poll. Request indirect messages being held by a coordinator.
Active Scan. Send Beacon Request to Broadcast Address (0xFFFF) and Broadcast
PAN (0xFFFF) on every channel. The parameter determines the time the radio will
listen for Beacons on each channel. A PanDescriptor is created and returned for every
Beacon received from the scan. Each PanDescriptor contains the following information:
CoordAddress (SH, SL)<CR>
CoordPanID (ID)<CR>
CoordAddrMode <CR>
Channel (CH parameter) <CR>
SecurityUse<CR>
ACLEntry<CR>
SecurityFailure<CR>
SuperFrameSpec<CR> (2 bytes):
GtsPermit<CR>
RSSI<CR> (RSSI is returned as -dBm)
TimeStamp<CR> (3 bytes)
<CR>
A carriage return <CR> is sent at the end of the AS command. The Active Scan is
capable of returning up to 5 PanDescriptors in a scan. The actual scan time on each
channel is measured as Time = [(2 ^SD PARAM) * 15.36] ms. Note the total scan time is
this time multiplied by the number of channels to be scanned (16 for the XBee and 13
for the XBee-PRO). Also refer to SD command description.
Energy Scan. Send an Energy Detect Scan. This parameter determines the length of
scan on each channel. The maximal energy on each channel is returned & each value
is followed by a carriage return. An additional carriage return is sent at the end of the
command. The values returned represent the detected energy level in units of -dBm.
The actual scan time on each channel is measured as Time = [(2 ^ED) * 15.36] ms.
Note the total scan time is this time multiplied by the number of channels to be scanned
(refer to SD parameter).
AES Encryption Enable. Disable/Enable 128-bit AES encryption support. Use in
conjunction with the KY command.
AES Encryption Key. Set the 128-bit AES (Advanced Encryption Standard) key for
encrypting/decrypting data. The KY register cannot be read.
© 2009 Digi Internatonal, Inc.
0x02 = 16-bit Short Address
0x03 = 64-bit Long Address
bit 15 - Association Permitted (MSB)
bit 14 - PAN Coordinator
bit 13 - Reserved
bit 12 - Battery Life Extension
bits 8-11 - Final CAP Slot
bits 4-7 - Superframe Order
bits 0-3 - Beacon Order
CH parameter of the End Device
received after sending the request
association complete
the ID parameter of the End Device
CCA failure
configured to support beacons
Parameter Range
0 - 0x13 [read-only]
-
-
0 - 6
0 - 6
0 - 1
0 - (any 16-Byte value)
Default
-
-
-
-
-
0 (disabled)
-
30