ATA5429-PLQW Atmel, ATA5429-PLQW Datasheet - Page 52
![IC TXRX ASK/FSK 915MHZ 48-QFN](/photos/7/34/73471/48-vqfn-6_543-5130_01-4_sml.jpg)
ATA5429-PLQW
Manufacturer Part Number
ATA5429-PLQW
Description
IC TXRX ASK/FSK 915MHZ 48-QFN
Manufacturer
Atmel
Specifications of ATA5429-PLQW
Frequency
915MHz
Data Rate - Maximum
20kbps
Modulation Or Protocol
ASK, FSK
Applications
Alarm, ISM, Telemetry
Power - Output
5dBm
Sensitivity
-112.5dBm
Voltage - Supply
2.4 V ~ 3.6 V or 4.4 V ~ 6.6 V
Current - Receiving
10.5mA
Current - Transmitting
10mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Operating Temperature
-40°C ~ 85°C
Package / Case
48-VQFN Exposed Pad, 48-HVQFN, 48-SQFN, 48-DHVQFN
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
7mm
Product Height (mm)
0.9mm
Product Length (mm)
7mm
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Memory Size
-
Lead Free Status / Rohs Status
Compliant
Other names
ATA5429-PLQW
ATA5429-PLQWTR
ATA5429-PLQWTR
9. Operation Modes
9.1
9.1.1
52
RX Operation
ATA5423/ATA5425/ATA5428/ATA5429
RX Polling Mode
The transceiver is set to RX operation with the bits OPM0 and OPM1 in control register 1.
Table 9-1.
The transceiver is designed to consume less than 1 mA in RX operation while remaining sensi-
tive to signals from a corresponding transmitter. This is achieved via the polling circuit. This
circuit enables the signal path periodically for a short time. During this time the bit-check logic
verifies the presence of a valid transmitter signal. Only if a valid signal is detected does the
transceiver remain active and transfer the data to the connected microcontroller. This transfer
takes place either via the TX/RX data buffer or via the pin SDO_TMDO. When there is no valid
signal present, the transceiver is in sleep mode most of the time, resulting in low current con-
sumption. This condition is called RX polling mode. A connected microcontroller can be disabled
during this time.
All relevant parameters of the polling logic can be configured by the connected microcontroller.
This flexibility enables the user to meet the specifications in terms of current consumption, sys-
tem response time, data rate, etc.
In RX mode the RF transceiver is enabled permanently and the bit-check logic verifies the pres-
ence of a valid transmitter signal. When a valid signal is detected the transceiver transfers the
data to the connected microcontroller. This transfer take place either via the TX/RX data buffer
or via the pin SDO_TMDO.
When the transceiver is in RX polling mode it stays in a continuous cycle of three different
modes. In sleep mode the RF transceiver is disabled for the time period T
low current of I
cessing circuits are enabled and settled. In the following bit-check mode, the incoming data
stream is analyzed bit by bit to see if it is a valid transmitter signal. If no valid signal is present,
the transceiver is set back to sleep mode after the period T
check as it is a statistical process. An average value for T
teristics. During T
and T
on pin RX_ACTIVE (see
rent consumption in RX polling mode I
application (6V) or Base-station Application (5V). To calculate I
by VS1,VS2 in 1 Li battery application (3V), VS2 in 2 Li battery application (6V) or VS2,VAUX in
Base-station Application (5V) (see section
I
P
=
I
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- -
IDLE_X
Bit-check
OPM1
the current consumption is I
1
1
T
Control Register 1
S
Sleep
= I
Startup_PLL
IDLE_X
+
T
I
Sleep
Startup_PLL_X
. During the start-up period, T
Figure 9-1 on page 54
+
T
the current consumption is I
Startup_PLL
T
Startup_PLL
+
P
OPM0
T
is different in 1 Li battery application (3V), 2 Li battery
S
Startup_Sig_Proc
0
1
“Electrical Characteristics: General” on page
= I
+
RX_X
I
RX_X
and
. The condition of the transceiver is indicated
Figure 9-2 on page
Startup_PLL
+
T
T
Startup_Sig_Proc
S
Bit-check
Bit_check
= I
Bit-check
Startup_PLL_X
and T
P
is given in the electrical charac-
the index X must be replaced
. This period varies check by
RX polling mode
Startup_Sig_Proc
+
T
Function
RX mode
. During T
Bitcheck
55). The average cur-
Sleep
while consuming
4841D–WIRE–10/07
, all signal pro-
Startup_Sig_Proc
67).