ATMEGA256RZBV-8AU Atmel, ATMEGA256RZBV-8AU Datasheet - Page 322

• Manufacturer Part Number: ATMEGA256RZBV-8AU
• Description: MCU ATMEGA2560/AT86RF230 100TQFP
• Manufacturer: Atmel
• Series: ATMEGAr

Specifications of ATMEGA256RZBV-8AU

• Frequency: 2.4GHz
• Modulation Or Protocol: 802.15.4 Zigbee
• Applications: ISM, ZigBee™
• Power - Output: 3dBm
• Sensitivity: -101dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 15.5mA
• Current - Transmitting: 16.5mA
• Data Interface: PCB, Surface Mount
• Memory Size: 256kB Flash, 4kB EEPROM, 8kB RAM
• Antenna Connector: PCB, Surface Mount
• Package / Case: 100-TQFP
• Wireless Frequency: 2.4 GHz
• Interface Type: JTAG, SPI
• Output Power: 3 dBm
• Operating Temperature Range: - 55 C to + 125 C
• For Use With: ATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Data Rate - Maximum: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: ATmega256

28.5
2549M–AVR–09/10
Addressing the Flash During Self-Programming
The Z-pointer is used to address the SPM commands. The Z pointer consists of the Z-registers
ZL and ZH in the register file, and RAMPZ in the I/O space. The number of bits actually used is
implementation dependent. Note that the RAMPZ register is only implemented when the pro-
gram space is larger than 64 Kbytes.
Since the Flash is organized in pages (see
be treated as having two different sections. One section, consisting of the least significant bits, is
addressing the words within a page, while the most significant bits are addressing the pages.
This is shown in
addressed independently. Therefore it is of major importance that the Boot Loader software
addresses the same page in both the Page Erase and Page Write operation. Once a program-
ming operation is initiated, the address is latched and the Z-pointer can be used for other
operations.
The (E)LPM instruction use the Z-pointer to store the address. Since this instruction addresses
the Flash byte-by-byte, also bit Z0 of the Z-pointer is used.
Figure 28-3. Addressing the Flash During SPM
Note:
Bit
RAMPZ
ZH (R31)
ZL (R30)
Z - REGISTER
The different variables used in
PROGRAM MEMORY
BIT
RAMPZ7
Z15
Z7
PAGE
23
15
PROGRAM
COUNTER
7
15
Figure
PAGE ADDRESS
WITHIN THE FLASH
ZPCMSB
RAMPZ6
PCMSB
Z14
Z6
22
14
28-3. Note that the Page Erase and Page Write operations are
6
PCPAGE
ATmega640/1280/1281/2560/2561
RAMPZ5
Figure 28-3
Z13
Z5
21
13
5
ZPAGEMSB
PAGEMSB
Table 29-7 on page
PCWORD
RAMPZ4
Z12
are listed in
Z4
20
12
4
WORD ADDRESS
WITHIN A PAGE
(Note:)
1
0
0
RAMPZ3
INSTRUCTION WORD
Z11
Table 28-9 on page
19
11
Z3
3
PAGE
338), the Program Counter can
RAMPZ2
Z10
Z2
18
10
2
PCWORD[PAGEMSB:0]:
329.
00
01
02
PAGEEND
RAMPZ1
Z9
Z1
17
9
1
RAMPZ0
16
Z8
Z0
8
0
322