XC09-009NSC Digi International/Maxstream, XC09-009NSC Datasheet - Page 12
![no-image](/images/no-image-200.jpg)
XC09-009NSC
Manufacturer Part Number
XC09-009NSC
Description
MOD RF 900MHZ 9600BPS W/RPSMA
Manufacturer
Digi International/Maxstream
Series
9XCite™r
Specifications of XC09-009NSC
Frequency
900MHz
Data Rate - Maximum
9.6kbps
Modulation Or Protocol
FHSS, FSK
Power - Output
6dBm
Sensitivity
-108dBm
Voltage - Supply
2.85 V ~ 5.5 V
Current - Receiving
45mA
Current - Transmitting
55mA
Data Interface
PCB, Through Hole
Antenna Connector
RP-SMA
Operating Temperature
0°C ~ 70°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Applications
-
Memory Size
-
9XCite™ OEM RF Module – Product Manual v2.1 [2007.01.04]
2.2.4. Sleep Modes
Software Sleep
Sleep Modes enable the module to enter states of low-power consumption when not in use. Three
software Sleep Modes are supported:
In order to enter Sleep Mode, one of the following conditions must be met (in addition to the mod-
ule having a non-zero SM parameter value):
Once in Sleep Mode, the radio modem does not transmit or receive data until it first returns to Idle
Mode. The return into Idle Mode is triggered by the de-assertion of the Sleep pin or the arrival of a
serial byte through Data In pin.
The following table lists MaxStream's Sleep Mode configurations and the requirements needed to
transition into and out of Sleep Mode:
Table 2‐01. Sleep Mode Configurations
Pin Sleep (SM = 1)
<Lowest Power Configuration> In order to achieve this low-power state, Pin 2 must be asserted
(high). The modem remains in Pin Sleep until the Sleep pin is de-asserted. The modem will com-
plete a transmission or reception before activating Pin Sleep.
After enabling Pin Sleep (SM (Sleep Mode) Parameter = 1), Pin 2 controls whether the XCite Mod-
ule is active or in Sleep Mode. When Pin 2 is asserted (high), the modem transitions to Sleep Mode
and remains in its lowest power-consuming state until the Sleep pin is de-asserted. The XCite
Module requires 40ms to transition from Sleep Mode to Idle Mode. Pin 2 is only active if the
modem is setup to operate in this mode; otherwise the pin is ignored. Once in Pin Sleep Mode,
CTS is de-asserted (high), indicating that data should not be sent to the modem. The PWR pin is
also de-asserted (low) when the modem is in Pin Sleep Mode
Note: The module will complete a transmission or reception before activating Pin Sleep.
Sleep Mode
Setting
Pin Sleep
(SM=1)
Serial Port Sleep
(SM=2)
Cyclic Sleep
(SM=3-8)
1.
2.
© 2007 MaxStream, Inc.
• Pin Sleep (Host Controlled)
• Serial Port Sleep (Wake on Serial Port activity)
• Cyclic Sleep (Wake on RF activity)
• Pin/Host-controlled
The module is idle (no data transmission or reception) for the amount of time defined by
the ST (Time before Sleep) parameter.
SLEEP pin is asserted.
Transition into
Sleep Mode
Microcontroller can shut down
and Wake-up modules. Assert
(high) Sleep Pin (Pin 2).
Note: Module will complete a
transmission or reception before
activating Pin Sleep.
Automatic transition into Sleep
Mode after user-defined period
of inactivity (no transmitting or
receiving). Period of inactivity set
using ST Command.
Transitions into and out of Sleep Mode in cycles (user-
selectable wake-up interval of time (½ second to 16
seconds) set by SM Command). The Cyclic Sleep interval
time must be shorter than “Wake-up Initializer Timer” (set by
LH Command).
(Can be forced into Idle Mode using Sleep Pin if PW (Pin
Wake-up) Command is issued.)
Transition out of
Sleep Mode
De-Assert (low) Sleep
pin (Pin 2)
When serial byte is
received on the DI pin
(Pin 4)
Related
Commands
SM
SM, ST
HT, LH, PW, SM, ST
Power
Consumption
20 µA
1 mA
typically 76 µA
(when sleeping)
12