XC09-009NSC Digi International/Maxstream, XC09-009NSC Datasheet - Page 17
![no-image](/images/no-image-200.jpg)
XC09-009NSC
Manufacturer Part Number
XC09-009NSC
Description
MOD RF 900MHZ 9600BPS W/RPSMA
Manufacturer
Digi International/Maxstream
Series
9XCite™r
Specifications of XC09-009NSC
Frequency
900MHz
Data Rate - Maximum
9.6kbps
Modulation Or Protocol
FHSS, FSK
Power - Output
6dBm
Sensitivity
-108dBm
Voltage - Supply
2.85 V ~ 5.5 V
Current - Receiving
45mA
Current - Transmitting
55mA
Data Interface
PCB, Through Hole
Antenna Connector
RP-SMA
Operating Temperature
0°C ~ 70°C
Package / Case
Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Applications
-
Memory Size
-
Table 3‐01. AT Commands
(Settable/Readable using X‐CTU Software, serial communications software or microcontroller)
9XCite™ OEM RF Module – Product Manual v2.1 [2007.01.04]
AT
Designator
CD
CN
CS
DB
DT
FH
HP
HV
MK
RE
SH
SL
VR
WR
3.3. Command Reference Tables
Command Name & Description
(RX LED signal).
Exit AT Command Mode. Explicitly exit radio modem from AT
Command Mode and return it to Idle Mode.
DO2 Configuration. Select behavior of DI2 (Digital Output 2)
between CTS and RS-485 options.
Receive Signal Strength. Returns the signal strength (in
decibels) of the last received packet.
Destination Address. Set the address that identifies the
destination of the RF packet. Only radio modems having
matching addresses can communicate with each other.
Force Wake-up Initializer. Force a Wake-up Initializer to be
sent on the next transmission. WR (Write) Command does not
need to be issued with FH Command.
Use only with cyclic sleep modes (SM = 3-8) active on remote
modems.
Channel *. Select “Hopping” or “Single Frequency” channel on
which the radio modem is to communicate. Channels are not
noninterfering.
Hardware Version. Read the hardware version of the modem.
Address Mask. Set address mask to configure local and
global address space.
Restore Defaults. Restore AT-settable parameters to the
factory default configuration.
Serial Number High. Read High 16 bits of unique serial
number of radio modem.
Serial Number Low. Read Low 16 bits of unique serial number
of radio modem.
Firmware Version. Read firmware version currently loaded on
radio modem.
Write. Write parameters to radio modem’s non-volatile
memory in order for changes to persist through next power-up
or reset.
DI3 Configuration. Redefines the RX LED I/O line
XCite AT Commands [below] and Non-AT Settable Parameters [next page] are organized under the
following
command categories:
© 2007 MaxStream, Inc.
• AT Command Mode Options
• Diagnostic
• Networking
• Serial Interfacing
• Sleep Mode (Low Power)
Parameter Range
0 – 2
--
0 – 4
0x25 – 0x6A
[Read-only]
--
Hopping:
Single Frequency):
Range: 0 – 0xFFFF
[Read-only]
0 – 0xFFFF
--
0 – 0xFFFF
[Read-only]
0 – 0xFFFF
[Read-only]
0 – 0xFFFF
[Read-only]
--
0 – 0xFFFF
0 = RX LED
1 = high
2 = low
0 = normal CTS
1 = RS-485 enable low
2 = high
3 = RS-485 enable high
4 = low
0 – 6
0 – 0x18
Command
Category
Serial
Interfacing
AT Command
Mode Options
Serial
Interfacing
Diagnostic
Networking
Sleep
(Low Power)
Networking
Diagnostic
Networking
(Special)
Diagnostic
Diagnostic
Diagnostic
(Special)
# Bytes
Returned
1
--
1
1
2
--
1
2
2
--
2
2
2
--
Factory
Default
0
--
0
--
0
--
0
--
0xFFFF
(65535d)
--
--
--
--
--
17