AC4486-5M Laird Technologies, AC4486-5M Datasheet - Page 28

• Manufacturer Part Number: AC4486-5M
• Description: TXRX 868MHZ 3V TTL 5MW RS232
• Manufacturer: Laird Technologies
• Series: AeroCommr

Specifications of AC4486-5M

• Frequency: 868MHz
• Data Rate - Maximum: 115.2kbps
• Modulation Or Protocol: FSK
• Applications: AMR, Gaming Devices, Inventory Tracking
• Power - Output: 5mW
• Sensitivity: -100dBm
• Voltage - Supply: 3.3V
• Current - Receiving: 30mA
• Current - Transmitting: 40mA
• Data Interface: Connector, 2 x 10 Header
• Antenna Connector: MMCX
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Board Size: 49 mm x 42 mm x 5 mm
• Output Power: 5 mW
• Antenna: External MMCX Connector
• Frequency Rf: 869.65MHz
• Transmit Power: 5mW
• Interface Type: Serial
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

AC4486 Specifications
4.6.9 Read Static Bank #1 Byte
The OEM Host issues this command to the transceiver to read Static Bank #1 Bytes. Static Bank #1 is
a bank of memory that holds many of the parameters that control the transceiver. Using the
Read/Write Static Bank #1 command allows these parameters to be changed dynamically. Because
the memory bank is static, when the transceiver is reset, these parameters will revert back to the
settings stored in EEPROM. Be careful not to change Static Bank addresses unless directed to do so
by AeroComm.
Host Command:
Transceiver Response:
4.6.10 W ite Static Bank #1 Byte
The Host issues this command to the transceiver to write Static Bank #1 Bytes. Static Bank #1 is a
bank of memory that holds many of the parameters that control the transceiver. Using the Read/Write
Static Bank #1 command allows these parameters to be changed dynamically. Because the memory
bank is static, when the transceiver is reset, these parameters will revert back to the settings stored in
EEPROM. Be careful not to change Static Bank addresses unless directed to do so by AeroComm.
Host Command:
Transceiver Response:
4.6.11 Read Static Bank #2 Byte
The Host issues this command to the transceiver to read Static Bank #2 Bytes. Static Bank #2 is a
bank of memory that holds many of the parameters that control the transceiver. Using the Read/Write
Static Bank #2 command allows these parameters to be changed dynamically. Because the memory
bank is static, when the transceiver is reset, these parameters will revert back to the settings stored in
EEPROM. Be careful not to change Static Bank addresses unless directed to do so by AeroComm.
Host Command:
Transceiver Response:
01/21/05
Byte 1 = CCh
Byte 2 = 0Ah
Byte 3 = 00 – FFh corresponding to a valid Static Bank #1 address
Byte 1 = CCh
Byte 2 = 00 – FFh corresponding to a valid Static Bank #1 address
Byte 1 = CCh
Byte 2 = 0Bh
Byte 3 = 00 – FFh corresponding to a valid Static Bank #1 address
Byte 4 = 00 – FFh corresponding to new value for address specified by Byte 3
Byte 1 = CCh
Byte 2 = 00 – FFh corresponding to a valid Static Bank #1 address
Byte 3 = 00 – FFh corresponding to new value for address specified by Byte 2
Byte 1 = CCh
Byte 2 = 0Ch
Byte 3 = 00 – FFh corresponding to a valid Static Bank #2 address
Byte 1 = CCh
r
28