ADF7021-NBCPZ Analog Devices Inc, ADF7021-NBCPZ Datasheet - Page 31

• Manufacturer Part Number: ADF7021-NBCPZ
• Description: IC TXRX 80-650/842-916MHZ 48LFCS
• Manufacturer: Analog Devices Inc

Specifications of ADF7021-NBCPZ

• Frequency: 80MHz ~ 650MHz, 842MHz ~ 916MHz
• Data Rate - Maximum: 33kbps
• Modulation Or Protocol: 2-FSK, 3-FSK, 4-FSK, MSK
• Applications: Keyless Entery, Pagers, WMTS
• Power - Output: -16dBm ~ 13dBm
• Sensitivity: -130dBm
• Voltage - Supply: 2.3 V ~ 6 V
• Current - Receiving: 26mA
• Current - Transmitting: 32.3mA @ 10dBm
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LFCSP
• Receiving Current: 26.4mA
• Transmitting Current: 20.2mA
• Data Rate: 24Kbps
• Frequency Range: 80MHz To 916MHz
• Modulation Type: FSK, MSK
• Rf Ic Case Style: LFCSP
• No. Of Pins: 48
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Product Depth (mm): 7mm
• Product Length (mm): 7mm
• Operating Supply Voltage (min): 2.3V
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF7021DBZ6 - BOARD EVAL ADF7021 608-614MHZEVAL-ADF7021DBZ5 - BOARD EVAL ADF7021EVAL-ADF7021DBZ3 - BOARD DAUGHTER FOR ADF7021EVAL-ADF7021DBZ2 - BOARD EVAL FOR ISM ADF7021
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant

The user has the option of changing the two threshold values
from the defaults of 30 and 70 (Register 9). The default AGC
setup values should be adequate for most applications. The
threshold values must be more than 30 apart for the AGC to
operate correctly.
Offset Correction Clock
In Register 3, the user should set the BBOS_CLK_DIVIDE bits
(R3_DB[4:5]) to give a baseband offset clock (BBOS CLK)
frequency between 1 MHz and 2 MHz.
where BBOS_CLK_DIVIDE can be set to 4, 8, 16, or 32.
AGC Information and Timing
AGC is selected by default and operates by setting the appropriate
LNA and filter gain settings for the measured RSSI level. It is
possible to disable AGC by writing to Register 9 if the user wants to
enter one of the modes listed in Table 15. The time for the AGC
circuit to settle and, therefore, the time it takes to measure the RSSI
accurately, is typically 390 μs. However, this depends on how many
gain settings the AGC circuit has to cycle through. After each gain
change, the AGC loop waits for a programmed time to allow
transients to settle. This AGC update rate is set according to
where:
AGC_CLK_DIVIDE is set by R3_DB[26:31]. A value of 13 is
recommended.
SEQ_CLK_DIVIDE = 100 kHz (R3_DB[18:25]).
Table 15. LNA/Mixer Modes
Receiver Mode
High Sensitivity
Mode (Default)
Enhanced Linearity
High Gain
Medium Gain
Enhanced Linearity
Medium Gain
Low Gain
Enhanced Linearity
Low Gain
BBOS CLK [Hz] = XTAL/(BBOS_CLK_DIVIDE)
AGC Update Rate [Hz] =
LNA_MODE
(R9_DB25)
0
0
1
1
1
1
SEQ
AGC
_
LNA_GAIN
(R9_DB[20:21])
30
30
10
10
3
3
CLK
_
CLK
_
DIVIDE
_
DIVIDE
[Hz]
MIXER_LINEARITY
(R9_DB28)
0
1
0
1
0
1
Rev. 0 | Page 31 of 64
By using the recommended setting for AGC_CLK_DIVIDE, the
total AGC settling time is
The worst case for AGC settling occurs when the AGC control
loop has to cycle through all five gain settings, which gives a
maximum AGC settling time of 650 μs.
RSSI Formula (Converting to dBm)
The RSSI formula is
where:
Readback Code is given by Bit RV7 to Bit RV1 in the Register 7
readback register (see Figure 58 and the Readback Format
section).
Gain Mode Correction is given by the values in Table 14.
The LNA gain (LG2, LG1) and filter gain (FG2, FG1) values
are also obtained from the readback register, as part of an RSSI
readback.
Table 14. Gain Mode Correction
LNA Gain
(LG2, LG1)
H (1, 0)
M (0, 1)
M (0, 1)
M (0, 1)
L (0, 0)
An additional factor should be introduced to account for losses
in the front-end-matching network/antenna.
Sensitivity (2FSK, DR =
4.8 kbps, f
−118
−114.5
−112
−105.5
−100
−92.3
Input Power [dBm] = −130 dBm + (Readback Code + Gain
AGC
Mode Correction) × 0.5
Settling
DEV
= 4 kHz)
Time
Filter Gain
(FG2, FG1)
H (1, 0)
H (1, 0)
M (0, 1)
L (0, 0)
L (0, 0)
[sec]
=
Rx Current
Consumption (mA)
24.6
24.6
22.1
22.1
22.1
22.1
Number
AGC
of
Update
AGC
Gain Mode
Correction
0
24
38
58
86
ADF7021-N
Gain
Rate
[Hz]
Changes
Input IP3
(dBm)
−24
−20
−13.5
−9
−5
−3