ATR2406-PNSG Atmel, ATR2406-PNSG Datasheet - Page 15

• Manufacturer Part Number: ATR2406-PNSG
• Description: IC IF ISM TXRX 2.4GHZ 32QFN
• Manufacturer: Atmel

Specifications of ATR2406-PNSG

• Frequency: 2.4GHz
• Data Rate - Maximum: 1.152Mbps
• Modulation Or Protocol: DSSS, GFSK
• Applications: Wireless Game Controllers
• Power - Output: 4dBm
• Sensitivity: -93dBm
• Voltage - Supply: 2.9 V ~ 3.6 V
• Current - Receiving: 57mA
• Current - Transmitting: 42mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -10°C ~ 60°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Memory Size: -
• Other names: ATR2406-PNSGCT; ATR2406-PNSGCT

7.10
4779N–ISM–12/08
Received Signal Strength Indication (RSSI)
Table 7-9.
The RSSI is given as an analog voltage at the RSSI pin. A typical plot of the RSSI value is
shown in
Figure 7-4.
Condition
C1
C2
C3
C4
C5
Figure
Description of the Conditions/States
Typical RSSI Value versus Input Power
7-4.
Description
Power down
ATR2406 is switched off and the supply current is lower than 1 µA.
Power up
ATR2406 is powered up by toggling PU_REG and PU_TRX to high.
PU_REG enables the external AUX regulator transistor including VCO regulator.
PU_TRX enables internal blocks like the PLL and the VCO.
Depending on the value of the external capacitors (for example, at the AUX
regulator, if one is used), it is necessary to wait at least 40 µs until the different
supply voltages have settled.
Programming
The internal register of the ATR2406 is programmed via the three-wire interface.
At TX, this is just the PLL (transmit channel) and the deviation (Gaussian filter).
At RX, this is just the PLL (receive channel) and, if the clock recovery is used, also
the bits to enable this option. At the start of the three-wire programming, the
enable signal is toggled from high to low to enable clocking the data into the
internal register. When the enable signal rises again to high, the programmed
data is latched. This is the time point at which the settling of the PLL starts. It is
necessary to wait the settling time of 200 µs so that the VCO frequency is stable.
The reference clock needs to be applied to ATR2406 for at least the time when the
PLL is in operation, which is the programming state (C3) and the active slot (C4,
C5). Out of the reference clock, several internal signals are also derived, for
example, the Gaussian filter circuitry and TX_DATA sampling.
This is the receive slot where the transmit burst is received and data as well as
recovered clock are available.
This is the active transmit slot. As soon as TX_DATA is applied to ATR2406, the
signal nOLE toggles to low which enables modulation in open-loop mode.
The preamble (1-0-1-0 pattern) should start being sent at the start of TX_ON.
2.0
0.0
2.5
0.5
1.0
1.5
-130
-110
-90
RF Level (dBm)
-70
-50
-30
-10
10
ATR2406
15