A16-1NRN Omron, A16-1NRN Datasheet - Page 201

• Manufacturer Part Number: A16-1NRN
• Description: NEON LAMP 110V RED FOR A16
• Manufacturer: Omron
• Type: Neon Lamp, 110 VoltsACr
• Series: A16r

Specifications of A16-1NRN

• Accessory Type: Neon Lamp Replacement
• Supply Voltage: 110V
• Base Type: Bi-Pin
• Colour: Red
• Current Rating: 1.5mA
• Svhc: No SVHC (15-Dec-2010)
• Illumination Colour: Red
• Operating Lifetime: 10000h
• Voltage Rating Vac: 110V
• Average Bulb Life: 1000
• Color: Red
• Illumination: Illuminated
• Height: 13 mm
• Illumination Color: Red
• Mounting Style: Snap In
• Termination Style: Tabs
• Lamp Base Type: Bi-Pin
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: A16 Series
• For Use With: Z1397 - SWTCH KNOB RND 3POS DPDT ILL REDZ1394 - SWTCH KNOB RND 2POS SPDT ILL REDZ1391 - SWTCH KNOB RND 2POS SPDT ILL REDZ1385 - SWITCH KNB RECT 3POS DPDT ILLZ1382 - SWITCH KNB RECT 2POS SPDT ILLZ1379 - SWITCH KNB RECT 2POS SPDT ILLZ1373 - SWITCH KNOB SQ 3-POS DPDT ILLZ1370 - SWITCH KNOB SQ 2-POS SPDT ILLZ1367 - SWITCH KNOB SQ 2-POS SPDT ILLZ1309 - SWITCH PB RND MOM DPDT ILLUM REDZ1305 - SWITCH PB RECT MOM DPDT ILLUMZ1301 - SWITCH PB SQ MOM DPDT ILLUM RED
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: A161NRN; Z1342

Move the lever in the direction indicated by the arrow in the following
figure, then pull the Operation Unit or the Switch Blocks.
Since the lever has a hole with an inside diameter of 6.5 mm, the
lever can be moved in the specified direction by inserting a screw-
driver into the hole and then moving the screwdriver.
Emergency Stop Switch
Insert the protrusion of the Tightening Wrench (A22Z-3905) into the
Cap slot and then turn to remove the Cap.
Installing/Replacing from the Panel
Surface
Insert the Lamp Extractor (A22Z-3901) into the lamp, then rotate the
Extractor while pressing it.
Installing/Replacing on the Switch
Grip the indicator with your fingers, then rotate the indicator while
pressing it against the Switch.
Assembling the Cap
Installing/Replacing the Lamp
Screwdriver
Mounting the Switch
The Standard-size Legend Plate Frame can be mounted. Mount the
Frame as shown in the following diagram. Mount the Switch in the
same way as for an ordinary panel.
Creating a Cable Port Hole
Place the tip of a screwdriver on the surface where the cable port
hole is to be created with the cover attached and strike the screw-
driver to punch a hole. Attempts to punch a hole on the other side of
the case will damage the Box.
Securing the Connector Cable
1. Insert the connector into the cable port hole in the Box and secure
2. Open a hole in the thin rubber section of the rubber ring.
3. Pass the tightening cap through the cable, insert the cable into
7 to 9 dia.
9 to 11 dia.
with the fixing nut inside the box.
the connector, and tighten the hexagonal nut to secure the cable.
Lock nut
Control Box (Enclosure)
Cable diameter
Inside
Box
Outside
Rubber washer
Connector
A22Z-3500-1
A22Z-3500-2
Snap-in Legend Plate
Tightening cap
Connector
Cable
199