LB15SKW01-C NKK Switches, LB15SKW01-C Datasheet - Page 9

• Manufacturer Part Number: LB15SKW01-C
• Description: SW PB SPDT MOM SQ RED CAP SLD MT
• Manufacturer: NKK Switches
• Series: LBr
• Type: Standardr

Specifications of LB15SKW01-C

• Circuit: SPDT
• Switch Function: On-Mom
• Contact Rating @ Voltage: 3A @ 125VAC
• Actuator Type: Square Button
• Mounting Type: Panel Mount, Snap-In
• Termination Style: Solder, Quick Connect - .110" (2.8mm)
• Pole Throw Configuration: SPDT
• Switch Configuration: ON ON
• Actuator Style: Square Button
• Current Rating (max): 3A
• Illumination Type: Not Required
• Ac Voltage Rating (max): 250VVAC
• Dc Voltage Rating (max): 30VVDC
• Contact Material: Silver Alloy
• Contact Plating: Silver
• Mechanical Life: 1000000
• Product Height (mm): 34mm
• Product Depth (mm): 17.8mm
• Operating Temp Range: -25C to 70C
• Mounting Style: Panel
• Terminal Type: Quick Connect/Solder
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Illumination Type, Color: -
• Illumination Voltage (nominal): -
• Lead Free Status / Rohs Status: Compliant
• Other names: LB15SKW01-C-RO; LB15SKW01-C-RO

NKK Switches • email: [e-mail] • Phone [phone] • Fax [phone] • www.nkkswitches.com
Match projection (C) on cap assembly
with groove (C) inside switch.
Snap-in clip holds all switches firmly
in place. To mount round switch,
match the antirotation projection
on switch with
guide cut in
panel. Snap
into panel
cutout.
Recommended Methods:
Laser Etch on clear lens;
Screen Print or Pad Print on lens.
Epoxy based ink is recommended.
Additional method for legends is engraving the cap. Maximum depth for engraving is .012” (0.3mm) on the cap lens.
Snap-in Mount
C
For other legend support options, customers may either contact the factory and request the LB Legend Packet,
C
Square
Projection
Panel
or utilize the general information and basic specifications presented below.
Easily create and submit your own legends using our new on-line Legend Maker.
Enamel paint is recommended to fill the engraved area.
(11.68) Sq
.460
(13.2) Sq
.520
ASSEMBLY INSTRUCTIONS
Insert switch from the front of the panel
with the o-ring between the built-in
bezel and the panel. Install mounting
nut AT075 (supplied
with switch) from the
rear of the panel.
Overtightening
mounting nut may
damage the switch
housing.
Suggested Printable Area for LB Lens
Standard Size Snap-in Pushbuttons
Match clip on cap assembly with
receptacle inside switch.
(0.76) Typ
.030
Additional Method
Round & Rectangular
Bushing Mount
LEGENDS
Visit www.nkkswitches.com
Panel Seal
Shaded areas are printable areas.
(17.48) Dia
.688
(19.0) Dia
.748
O-ring
Bezel
Mounting Nut
Panel
(0.76) Typ
.030
Projection
Notch
Match projection on cap assembly
with notch inside switch.
Cut Corner
(17.88)
.704
Series LB
Panel Seal
(19.4)
.764
Rubber Seal
Socket Wrench
Cap Extractor
(0.76) Typ
.030
(11.68)
(0.76) Typ
.030
.460
AT109
(13.2)
.520
AT112
Projection
03-07