S9S08DN32F1MLH Freescale Semiconductor, S9S08DN32F1MLH Datasheet - Page 281

• Manufacturer Part Number: S9S08DN32F1MLH
• Description: IC MCU 8BIT 32KB FLASH 64LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of S9S08DN32F1MLH

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 64-LQFP
• Processor Series: S08D
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 8
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08DZ60
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.6.2.1.2
When CPWMS=1, TOF gets set when the timer counter changes direction from up-counting to
down-counting at the end of the terminal count (the value in the modulo register). In this case the TOF
corresponds to the end of a PWM period.
15.6.2.2
The meaning of channel interrupts depends on the channel’s current mode (input-capture, output-compare,
edge-aligned PWM, or center-aligned PWM).
15.6.2.2.1
When a channel is configured as an input capture channel, the ELSnB:ELSnA control bits select no edge
(off), rising edges, falling edges or any edge as the edge which triggers an input capture event. When the
selected edge is detected, the interrupt flag is set. The flag is cleared by the two-step sequence described
in
15.6.2.2.2
When a channel is configured as an output compare channel, the interrupt flag is set each time the main
timer counter matches the 16-bit value in the channel value register. The flag is cleared by the two-step
sequence described
15.6.2.2.3
For channels configured for PWM operation there are two possibilities. When the channel is configured
for edge-aligned PWM, the channel flag gets set when the timer counter matches the channel value register
which marks the end of the active duty cycle period. When the channel is configured for center-aligned
PWM, the timer count matches the channel value register twice during each PWM cycle. In this CPWM
case, the channel flag is set at the start and at the end of the active duty cycle period which are the times
when the timer counter matches the channel value register. The flag is cleared by the two-step sequence
described
15.7
Freescale Semiconductor
Section 15.6.2, “Description of Interrupt Operation.”
1. Write to TPMxCNTH:L registers
2. Read of TPMxCNTH:L registers
(TPMxCNTH:TPMxCNTL)) [SE110-TPM case 7]
Any write to TPMxCNTH or TPMxCNTL registers in TPM v3 clears the TPM counter
(TPMxCNTH:L) and the prescaler counter. Instead, in the TPM v2 only the TPM counter is cleared
in this case.
(TPMxCNTH:TPMxCNTL))
— In TPM v3, any read of TPMxCNTH:L registers during BDM mode returns the value of the
The Differences from TPM v2 to TPM v3
Section 15.6.2, “Description of Interrupt Operation.”
TPM counter that is frozen. In TPM v2, if only one byte of the TPMxCNTH:L registers was
read before the BDM mode became active, then any read of TPMxCNTH:L registers during
Channel Event Interrupt Description
Center-Aligned PWM Case
Input Capture Events
Output Compare Events
PWM End-of-Duty-Cycle Events
Section 15.6.2, “Description of Interrupt Operation.”
MC9S08DN60 Series Data Sheet, Rev 3
(Section 15.3.2, “TPM-Counter Registers
(Section 15.3.2, “TPM-Counter Registers
Chapter 15 Timer/PWM Module (S08TPMV3)
281