EA EDIP240J-7LWTP ELECTRONIC ASSEMBLY, EA EDIP240J-7LWTP Datasheet - Page 6
![LCD Graphic Display Modules & Accessories White/Black Contrast With Touch Screen](/photos/15/62/156275/ea_edip240j-7lwtp_sml.jpg)
EA EDIP240J-7LWTP
Manufacturer Part Number
EA EDIP240J-7LWTP
Description
LCD Graphic Display Modules & Accessories White/Black Contrast With Touch Screen
Manufacturer
ELECTRONIC ASSEMBLY
Datasheet
1.EA_EDIP240J-7LATP.pdf
(21 pages)
Specifications of EA EDIP240J-7LWTP
Pixel Density
240 x 128
Fluid Type
FSTN Positive
Module Size (w X H X T)
113 mm x 70 mm x 13 mm
Viewing Area (w X H)
91.18 mm x 56.3 mm
Backlighting
White
Background Color
Black
Operating Temperature Range
- 20 C to + 70 C
Attached Touch Screen
Yes
Interface
RS-232, I2C BUS, or SPI BUS
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
EA eDIP240-7
Page 6
SPI INTERFACE
Wiring the display as shown below activates SPI mode. Data is then transferred over the serial,
synchronous SPI interface. The DORD, CPOL and CPHA inputs are used to match the hardware
conditions to the master. For
example (see diagram below).
A reasonable communication is
possible up to 100 kHz.
Clock frequency may be rised up to
3 MHz, but in this case make shure,
that there is a pause between 2
bytes of min. 100 µs.
level to indicate that data is available to be
fetched from the internal send buffer. This
line can, for instance, be connected to an
interrupt input of the host system.
DATA TRANSFER SPI
Via the pins DORD, CPOL and CPHA transfer
parameter will be set.
Write operation: a clock rate up to 100 kHz is allowed
without any stop. Together with a pause of 100 µs
between every data byte a clock rate up to 3 MHz an be
reached.
Read operation: to read data (e.g. the "ACK" byte) a
dummy byte (e.g . 0xFF) need to be sent. Note that the
EA eDIP240-7 for internal operation does need a short
time before providing the data; therefore a short pause of
min. 6µs (no activity of CLK line) is needed for each byte.
Same is with 100kHz operation.
Note:
At pin 20 (SBUF), the display sets a low
Application example
Pin
10
11 SPIMODE
12
13
14
15
16
17 EEP_SDA Bidir. Serial Data Line for int. EEPROM
18 EEP_SCL
19 EEP_WP
20
1
2
3
4
5
6
7
8
9
Symbol
RESET
VOUT
DORD
DPOM
CPOL
CPHA
VADJ
OUT2
BUZZ
SBUF
MOSI
MISO
TEST
GND
VDD
CLK
SS
In/Out Function
Out
Out
Out
Out
Out
Out
IN
In
In
In
In
In
In
In
In
In
In
-
-
-
Ground Potential for logic (0V)
Power supply for logic (+5V)
Operating voltage for LC driving
(input)
Output voltage for LC driving
L: Reset
Slave Select
Serial In
Serial Out
Shift Clock
Data Order (0=MSB first; 1=LSB first)
connect to GND for SPI interface
open-drain with internal pullup 20..50k
(V1.6 or later)
L: disable Power-On-Macro
do not connect for normal operation
Clock Polarity (0=LO 1=HI when idle)
Clock Phase
(sampled on 0=1st 1=2nd edge)
Buzzer output
Serial Clock Line for int. EEPROM
H: Write Protect for int. EEPROM
open-drain with internal pullup 20..50k
IN (Power-On) L: Testmode
OUT L: data in sendbuffer
Pinout eDIP240-7
SPI mode
Pin Symbol Function
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Specifications may be changed without
prior notice. Printing error reserved
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected
not connected