TZC3Z030A110R00 Murata, TZC3Z030A110R00 Datasheet - Page 13

• Manufacturer Part Number: TZC3Z030A110R00
• Description: Trimmer / Variable Capacitors 1.4 - 3PF 100V NPO+3
• Manufacturer: Murata
• Series: TZC3r

Specifications of TZC3Z030A110R00

• Tolerance: 0.1 %
• Voltage Rating: 100 Volts
• Operating Temperature Range: - 25 C to + 85 C
• Termination Style: SMD/SMT
• Product: Trimmer Capacitors - Ceramic Dielectric
• Dimensions: 0.126 in W x 0.177 in L x 0.063 in H
• Q Minimum: 300
• Temperature Coefficient: NP0 +/- 300 PPM / C
• Test Frequency: 1 MHz
• Capacitance Range: 3 pF
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Do not use the trimmer capacitor under atmosphere
2. Before using trimmer capacitor, please store under
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Do not store under direct sunlight.
1. Soldering
1. Use suitable screwdrivers that fit comfortably in
Before using trimmer capacitor, please test after
assembly in your particular mass production system.
(1) TZS2 series can be soldered by reflow soldering
(2) Soldering condition
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
(5) When using soldering iron, the diameter of the
(1) Recommended screwdriver for manual adjustment
(2) Recommended screwdriver bit for automatic
Notice (Storage and Operating Condition)
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
the condition of -10 to +40 degrees C and 30 to
85%RH.
Notice (Soldering and Mounting)
Notice (Handling)
driver slot.
Notice (Other)
adjustment
method and soldering iron. Do not use flow
soldering method (dipping).
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature,
the trimmer capacitor may deviate from the
specified characteristics.
from 100 micro m to 150 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering.
Insufficient amounts of solder can lead to
insufficient soldering strength on PCB.
Excessive amounts of solder may cause bridging
between the terminals or contact failure due to
flux wicking up.
string solder should be less than 0.5mm. The
string solder should be applied to the lower part
of the terminal only. Do not apply flux except
to the terminals. Excessive amounts of solder
and/or applying solder to the upper part of the
terminal may cause fixed metal rotor or contact
failure due to flux invasion into the movable
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
MURATA: KMDR050
MURATA: KMBT050
6. Do not use the trimmer capacitor under the
2. Mounting
2. When adjusting with a screwdriver, do not apply
3. Do not apply adhesive, lock paints, or any other
3. Cleaning
4. Other
(1) Corrosive gasses atmosphere
(2) In liquid (ex. water, oil, medical liquid,
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(6) Our recommended chlorine content of solder is
(7) Do not use water-soluble flux (for water
(1) Do not apply excessive force (preferably 5.0 N
(2) Do not warp and/or bend PCB to prevent trimmer
(3) Use the suitable dimension of the pick-up nozzle
conditions listed below.
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. If excessive force
is applied to the screwdriver slot, it may cause
deformation of the products.
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Cannot be cleaned because of open construction.
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
organic solvent, etc.)
part and/or the contact point. The soldering
iron should not come in contact with the
monolithic stator of the trimmer capacitor.
If such contact does occur, the trimmer
capacitor may be damaged.
as follows.
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
capacitor from breakage.
(1.8mm external diameter and 1.3mm bore
diameter).
11
T13E.pdf
08.8.27
2