TZC3Z030A110R00 Murata, TZC3Z030A110R00 Datasheet - Page 33

• Manufacturer Part Number: TZC3Z030A110R00
• Description: Trimmer / Variable Capacitors 1.4 - 3PF 100V NPO+3
• Manufacturer: Murata
• Series: TZC3r

Specifications of TZC3Z030A110R00

• Tolerance: 0.1 %
• Voltage Rating: 100 Volts
• Operating Temperature Range: - 25 C to + 85 C
• Termination Style: SMD/SMT
• Product: Trimmer Capacitors - Ceramic Dielectric
• Dimensions: 0.126 in W x 0.177 in L x 0.063 in H
• Q Minimum: 300
• Temperature Coefficient: NP0 +/- 300 PPM / C
• Test Frequency: 1 MHz
• Capacitance Range: 3 pF
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Soldering
1. Use suitable screwdrivers that fit comfortably in
2. When adjusting with a screwdriver, do not apply
Before using trimmer capacitor, please test after
assembly in your particular mass production system.
(1) Can be soldered by reflow soldering method, flow
(2) Soldering condition
(3) The amount of solder is critical.
(4) The thickness of solder paste should be printed
(5) When using soldering iron, the string solder
(6) Our recommended chlorine content of solder is
(1) Recommended screwdriver for manual adjustment
(2) Recommended screwdriver bit for automatic
Notice (Soldering and Mounting)
Notice (Handling)
driver slot.
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. If excessive force
is applied to the screwdriver slot, it may cause
deformation of the products.
Notice (Other)
(a) Solder paste: 0.2wt% max.
(b) String solder: 0.5wt% max.
soldering method, and soldering iron.
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
excessive time and/or excessive temperature, the
trimmer capacitor may deviate from the specified
characteristics.
from 150 micro m to 200 micro m and the dimension
of land pattern should be Murata's standard land
pattern used at reflow soldering. Insufficient
amounts of solder can lead to insufficient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the terminals
or contact failure due to flux wicking up.
should be applied to the lower part of the
terminal only. Do not apply flux except to the
terminals. Excessive amounts of solder and/or
applying solder to the upper part of the
terminal may cause fixed rotor or contact failure
due to flux invasion into the movable part and/or
the contact point. The soldering iron should not
come in contact with the plastic case of the
trimmer capacitor. If such contact does occur,
the trimmer capacitor may be damaged.
as follows.
adjustment
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
MURATA: KMDR010
MURATA: KMBT010
2. Mounting
3. Do not apply adhesive, lock paints, or any other
4. Do not break the cover film before the completion
5. Do not clean the trimmer capacitor after the cover
6. To break the cover film, first turn the screwdriver
3. Cleaning [with cover film type]
4. Other
(7) Do not use water-soluble flux (for water
(1) Do not apply excessive force (preferably 5.0N
(2) Do not warp and/or bend PCB to prevent trimmer
(3) In case of bending the terminals, do not apply
(4) Use the suitable dimension of the pick-up nozzle.
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
of PCB mounting, soldering, and cleaning.
film has been broken.
more than 360 deg., and set the capacitance value.
(Only inserting the screwdriver cannot break the
cover film.)
Isopropyl alcohol and Ethyl alcohol are available
material for cleaning. If you use any other types
of solvents, please evaluate performance by
your set. Moreover, please confirm no damage for
trimmer capacitor after cleaning by your conditions.
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
cleaning). To prevent the deterioration of
trimmer capacitor characteristics, apply flux
only to terminals.
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
capacitor from breakage.
excessive force to the body of the product and
prevent the terminal fixing part from damaging.
> Without cover film type
> With cover film type
- External dimensions of 4.5x4.0mm and
- 4.0mm external diameter and 2.0mm bore
2.5mm bore diameter.
diameter.
31
T13E.pdf
08.8.27
7