TZC3Z030A110R00 Murata, TZC3Z030A110R00 Datasheet - Page 38

• Manufacturer Part Number: TZC3Z030A110R00
• Description: Trimmer / Variable Capacitors 1.4 - 3PF 100V NPO+3
• Manufacturer: Murata
• Series: TZC3r

Specifications of TZC3Z030A110R00

• Tolerance: 0.1 %
• Voltage Rating: 100 Volts
• Operating Temperature Range: - 25 C to + 85 C
• Termination Style: SMD/SMT
• Product: Trimmer Capacitors - Ceramic Dielectric
• Dimensions: 0.126 in W x 0.177 in L x 0.063 in H
• Q Minimum: 300
• Temperature Coefficient: NP0 +/- 300 PPM / C
• Test Frequency: 1 MHz
• Capacitance Range: 3 pF
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Soldering
1. Use suitable screwdrivers that fit comfortably in
Before using trimmer capacitor, please test after
assembly in your particular mass production system.
36
(1) TZ03 series can be soldered by flow soldering
(2) Soldering condition
(3) The dimension of mounting hole should be Murata's
(4) When using soldering iron, the string solder
(5) Our recommended chlorine content of string
(6) Do not use water-soluble flux (for water cleaning).
(1) Recommended screwdriver for manual adjustment
(2) Recommended screwdriver bit for automatic
Notice (Soldering and Mounting)
Notice (Handling)
driver slot.
Notice (Other)
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
method and soldering iron. Do not use reflow
soldering method.
excessive time and/or excessive temperature,
the trimmer capacitor may deviate from the
specified characteristics.
standard mounting hole used at flow soldering.
The amount of solder is critical. Insufficient
amounts of solder can lead to insufficient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the terminals
or contact failure due to flux wicking up.
should be applied to the lower part of the
terminal only. Do not apply flux except to the
terminals. Excessive amounts of solder and/or
applying solder to the upper part of the
terminal may cause fixed rotor or the contact
failure due to flux invasion into the movable
part and/or the contact point. The soldering
iron should not come in contact with the plastic
case of the trimmer capacitor. If such contact
does occur, the trimmer capacitor may be damaged.
solder is 0.5wt% max.
To prevent the deterioration of trimmer
capacitor characteristics, apply flux only to
terminals.
adjustment
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
MURATA: KMDR010
MURATA: KMBT010
2. When adjusting with a screwdriver, do not apply
3. Do not apply adhesive, lock paints, or any other
2. Mounting
3. Cleaning
4. Other
(1) Do not apply excessive force (preferably 5.0 N
(2) Use the suitable PCB holes which are the same
(3) Do not apply bending stress more than 10.0N
(4) Mount trimmer capacitor in contact with PCB.
(5) In case of bending the terminals, do not apply
excessive force (preferably 1.0 N [Ref: 100gf] max.)
to minimize capacitance drift. If excessive force
is applied to the screwdriver slot, it may cause
deformation of the products.
substances to the trimmer capacitor to secure the
rotor position. They may cause corrosion or
electrical contact problems.
Isopropyl alcohol and Ethyl alcohol are available
material for cleaning. If you use any other types
of solvents, please evaluate performance by
your set. Moreover, please confirm no damage for
trimmer capacitor after cleaning by your conditions.
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
pitch as the terminal of the trimmer capacitor.
If it would not fit with the terminal, the
excessive stress would be applied to the
terminal and the trimmer capacitor may deviate
from the specified characteristics.
(Ref: 1kgf) after the trimmer capacitor has
been mounted on the PCB.
excessive force to the body of the product and
prevent the terminal fixing part from damaging.
T13E.pdf
08.8.27