PMF8118TP Ericsson Power Modules, PMF8118TP Datasheet - Page 38

• Manufacturer Part Number: PMF8118TP
• Description: DC/DC Converters & Regulators 0.8-1.8V 10A Non-Iso Input 12V 18W
• Manufacturer: Ericsson Power Modules
• Series: PMFr

Specifications of PMF8118TP

• Output Power: 18 W
• Input Voltage Range: 10.8 V to 13.2 V
• Number Of Outputs: 1
• Output Voltage (channel 1): 0.8 V to 1.8 V
• Output Current (channel 1): 10 A
• Package / Case Size: DIP
• Output Type: POLA Non-Isolated Regulator
• Product: Non-Isolated / POL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

EMC Specification
Conducted EMI measured according to test set-up.
The fundamental switching frequency is 350 kHz for PMF
8518L @ V
12 V, max I
Conducted EMI Input terminal value (typ)
EMI without filter
Test set-up
Layout recommendation
The radiated EMI performance of the DC/DC regulator will
depend on the PCB layout and ground layer design.
It is also important to consider the stand-off of the DC/DC
regulator.
If a ground layer is used, it should be connected to the output
of the DC/DC regulator and the equipment ground or chassis.
A ground layer will increase the stray capacitance in the PCB
and improve the high frequency EMC performance.
Prepared (also subject responsible if other)
SEC/D KEVIN YAN
Approved
SEC/D (Wei Zhang A)
PMF 8000 series
PMF 8000 series
PMF 8000 series
POL regulator, Input 10.8-13.2 V, Output 10 A/55 W
POL regulator, Input 10.8-13.2 V, Output 10 A/55 W
POL regulator, Input 10.8-13.2 V, Output 10 A/55 W
I
O
= 12 V, max I
.
O
and 250 kHz for PMF 8118T @ V
TBD
TBD
Checked
I
=
PRODUCT SPEC.
No.
3/1301-BMR 643 8 Uen
Date
2006-02-08
Output ripple and noise
Output ripple and noise measured according to figure below.
See Design Note 022 for detailed information.
Output ripple and noise test setup
Operating information
Extended information for POLA products is found in
Application Note POLA.
Input Voltage
The input voltage range 10.8 to 13.2 Vdc makes the product
easy to use in intermediate bus applications when powered
by a regulated bus converter.
Turn-off Input Voltage
The DC/DC regulators monitor the input voltage and will turn
on and turn off at predetermined levels.
The minimum hysteresis between turn on and turn off input
voltage is 50mV.
Remote Control (RC) Inhibit
The regulator will turn on when the input voltage is applied
with the INHIBIT pin open. Turn off is achieved by connecting
the INHIBIT pin to the - In. To ensure safe turn off, the voltage
difference between INHIBIT pin and the - In pin shall be less
than 0.6V. The regulator will restart automatically when this
connection is opened.
Technical Specifi cation
Technical Specifi cation
Technical Specifi cation
EN/LZT 146 318 R1B February 2006
EN/LZT 146 318 R1B April 2006
EN/LZT 146 318 R1C Sep 2006
© Ericsson Power Modules AB
© Ericsson Power Modules AB
© Ericsson Power Modules AB
Rev
A
The products are fitted with a
remote control function referenced
to the primary negative input
connection (- In), positive logic. The
INHIBIT function allows the
regulator to be turned on/off by an
external device like a
semiconductor or mechanical
switch. The INHIBIT pin has an
internal pull up resistor to + In.
Reference
1 (5)
38