STM32F100R6H6B STMicroelectronics, STM32F100R6H6B Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STM32F100R6H6B
Manufacturer Part Number
STM32F100R6H6B
Description
IC ARM CORTEX MCU 32KB 64TFBGA
Manufacturer
STMicroelectronics
Series
STM32r
Datasheet
1.STM32F100R4T6B.pdf
(87 pages)
Specifications of STM32F100R6H6B
Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
24MHz
Connectivity
I²C, IrDA, LIN, SPI, UART/USART
Peripherals
DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
Number Of I /o
51
Program Memory Size
32KB (32K x 8)
Program Memory Type
FLASH
Ram Size
4K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x12b; D/A 2x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
64-TFBGA
Core
ARM Cortex M3
For Use With
STM32100B-EVAL - EVAL BOARD FOR STM32F100VBT6
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM32F100R6H6B
Manufacturer:
STMicroelectronics
Quantity:
10 000
STM32F100x4, STM32F100x6, STM32F100x8, STM32F100xB
2.2.6
2.2.7
2.2.8
2.2.9
2.2.10
External interrupt/event controller (EXTI)
The external interrupt/event controller consists of 18 edge detector lines used to generate
interrupt/event requests. Each line can be independently configured to select the trigger
event (rising edge, falling edge, both) and can be masked independently. A pending register
maintains the status of the interrupt requests. The EXTI can detect an external line with a
pulse width shorter than the Internal APB2 clock period. Up to 80 GPIOs can be connected
to the 16 external interrupt lines.
Clocks and startup
System clock selection is performed on startup, however the internal RC 8 MHz oscillator is
selected as default CPU clock on reset. An external 4-24 MHz clock can be selected, in
which case it is monitored for failure. If failure is detected, the system automatically switches
back to the internal RC oscillator. A software interrupt is generated if enabled. Similarly, full
interrupt management of the PLL clock entry is available when necessary (for example on
failure of an indirectly used external crystal, resonator or oscillator).
Several prescalers allow the configuration of the AHB frequency, the high-speed APB
(APB2) and the low-speed APB (APB1) domains. The maximum frequency of the AHB and
the APB domains is 24 MHz.
Boot modes
At startup, boot pins are used to select one of three boot options:
●
●
●
The boot loader is located in System Memory. It is used to reprogram the Flash memory by
using USART1. For further details please refer to AN2606.
Power supply schemes
●
●
●
Power supply supervisor
The device has an integrated power on reset (POR)/power down reset (PDR) circuitry. It is
always active, and ensures proper operation starting from/down to 2 V. The device remains
in reset mode when V
external reset circuit.
The device features an embedded programmable voltage detector (PVD) that monitors the
V
generated when V
DD
/V
Boot from user Flash
Boot from system memory
Boot from embedded SRAM
V
Provided externally through V
V
RCs and PLL (minimum voltage to be applied to V
used).
V
V
registers (through power switch) when V
DD
SSA
DDA
BAT
DDA
= 2.0 to 3.6 V: External power supply for I/Os and the internal regulator.
, V
= 1.8 to 3.6 V: Power supply for RTC, external clock 32 kHz oscillator and backup
power supply and compares it to the V
and V
DDA
SSA
= 2.0 to 3.6 V: External analog power supplies for ADC, DAC, Reset blocks,
DD
must be connected to V
/V
DD
DDA
is below a specified threshold, V
drops below the V
Doc ID 16455 Rev 6
DD
pins.
DD
DD
PVD
and V
is not present.
PVD
threshold and/or when V
SS
threshold. An interrupt can be
DDA
, respectively.
POR/PDR
is 2.4 V when the ADC or DAC is
, without the need for an
DD
/V
DDA
Description
is higher
15/87